PCB_Cmd-SetCurrentLayerSetCurrentLayer_AD

Created: августа 03, 2017 | Updated: марта 06, 2024 | Applies to versions: 1.0, 1.1, 2.0, 2.1, 3.0, 3.1, 3.2 and 4

Вы просматриваете версию 2.1. Для самой новой информации, перейдите на страницу PCB_Cmd-SetCurrentLayer((SetCurrentLayer))_AD для версии 5

This documentation page references Altium NEXUS/NEXUS Client (part of the deployed NEXUS solution), which has been discontinued. All your PCB design, data management and collaboration needs can now be delivered by Altium Designer and a connected Altium 365 Workspace. Check out the FAQs page for more information.

Parent page: PCB Commands

The following pre-packaged resources, derived from this base command, are available:

Cycle to Next Signal Layer

Applied Parameters: LayerName = NextSignal

Summary

This command is used to quickly switch to the next enabled signal layer.

Access

This command is accessed from the PCB Editor and PCB Library Editor with the main workspace in focus by using the * key on the numeric keypad.

Use

After launching the command, the next enabled signal layer will become the current layer as distinguished by its associated layer tab becoming the active tab.

Use the command repeatedly to cycle forward (to the right among the layer tabs) through all enabled signal layers.

Tips

The various signal layers in the design can be enabled/disabled from the Layers section on the Layers & Colors tab of the View Configuration panel.
To set the current layer to a specific signal layer directly, click on the required signal layer tab at the bottom of the main design window.

Cycle to Previous Signal Layer

Applied Parameters: LayerName = PreviousSignal

Summary

This command is used to quickly switch to the previous enabled signal layer.

Access

This command is accessed from the PCB Editor and PCB Library Editor with the main workspace in focus, by using the Shift+* keys (using the * on the numeric keypad.

This command is only available with the editor in 2D viewing mode, since in 3D mode the Shift key is used to access the directional sphere.

Use

After launching the command, the previous enabled signal layer will become the current layer as distinguished by its associated layer tab becoming the active tab.

Use the command repeatedly to cycle back (to the left among the layer tabs) through all enabled signal layers.

Tips

The various signal layers in the design can be enabled/disabled from the Layers section on the Layers & Colors tab of the View Configuration panel.
To set the current layer to a specific signal layer directly, click on the required signal layer tab at the bottom of the main design window.

Cycle to Next Layer

Applied Parameters: LayerName = Next

Summary

This command is used to quickly switch to the next enabled layer.

Access

This command is accessed from the PCB Editor and PCB Library Editor with the main workspace in focus by using the + key on the numeric keypad.

Use

After launching the command, the next enabled layer will become the current layer as distinguished by its associated layer tab becoming the active tab.

Use the command repeatedly to cycle forward (to the right among the layer tabs) through all enabled layers.

Tips

The various layers in the design can be enabled/disabled from the Layers section on the Layers & Colors tab of the View Configuration panel.
To set the current layer to a specific layer directly, click on the required signal layer tab at the bottom of the main design window.

Cycle to Previous Layer

Applied Parameters: LayerName = Previous

Summary

This command is used to quickly switch to the previous enabled layer.

Access

This command is accessed from the PCB Editor and PCB Library Editor with the main workspace in focus, by using the - keyboard shortcut on the numeric keypad.

Use

After launching the command, the previous enabled layer will become the current layer as distinguished by its associated layer tab becoming the active tab.

Use the command repeatedly to cycle back (to the left among the layer tabs) through all enabled layers.

Tips

The various layers in the design can be enabled/disabled from the Layers section on the Layers & Colors tab of the View Configuration panel.
To set the current layer to a specific layer directly, click on the required signal layer tab at the bottom of the main design window.

Версия для печати

If you find an issue, select the text/image and pressCtrl + Enterto send us your feedback.

PCB_Cmd-SetCurrentLayerSetCurrentLayer_AD

Summary

Access

Use

Tips

Summary

Access

Use

Tips

Summary

Access

Use

Tips

Summary

Access

Use

Tips

Was this page helpful?