PCB_Cmd-SnapGridXYSnapGridXY_AD

Created: августа 03, 2017 | Updated: марта 11, 2019 | Applies to versions: 18.0, 18.1, 19.0, 19.1, 20.0, 20.1, 20.2 and 21

Вы просматриваете версию 18. Для самой новой информации, перейдите на страницу PCB_Cmd-SnapGridXY((SnapGridXY))_AD для версии 22

Parent page: PCB Commands

The following pre-packaged resources, derived from this base command, are available:

Set Snap Grid X to 1Mil

Applied Parameters: Axis=X|Value=1Mil

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 1mil. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 1 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 1 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 1mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 5Mil

Applied Parameters: Axis=X|Value=5Mil

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 5mil. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 5 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 5 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 5mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 10Mil

Applied Parameters: Axis=X|Value=10Mil

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 10mil. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 10 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 10 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 10mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 20Mil

Applied Parameters: Axis=X|Value=20Mil

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 20mil. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 20 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 20 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 20mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 25Mil

Applied Parameters: Axis=X|Value=25Mil

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 25mil. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 25 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 25 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 25mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 50Mil

Applied Parameters: Axis=X|Value=50Mil

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 50mil. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 50 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 50 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 50mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 100Mil

Applied Parameters: Axis=X|Value=100Mil

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 100mil. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 100 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 100 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 100mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 0.025mm

Applied Parameters: Axis=X|Value=0.025MM

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 0.025mm. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 0.025 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 0.025 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 0.025mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 0.100mm

Applied Parameters: Axis=X|Value=0.100MM

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 0.100mm. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 0.100 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 0.100 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 0.100mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 0.250mm

Applied Parameters: Axis=X|Value=0.250MM

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 0.250mm. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 0.250 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 0.250 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 0.2500mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 0.500mm

Applied Parameters: Axis=X|Value=0.500MM

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 0.500mm. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 0.500 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 0.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 0.500mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 1.000mm

Applied Parameters: Axis=X|Value=1.000MM

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 1.000mm. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » 1.000 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 1.000 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 1.000mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X to 2.500mm

Applied Parameters: Axis=X|Value=2.500MM

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to 2.500mm. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the 2.500 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » 2.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step X property of the default Global Board Snap Grid will be set to 2.500mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid X

Applied Parameters: Axis=X

Summary

This command is used to set the X (horizontal) step value - for the default Global Board Snap Grid - to a chosen value. This value, together with the Y (vertical) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid X » Set Snap Grid command from the pop-up menu.
PCB Editor - choosing the Snap Grid X » Set Snap Grid entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the Snap Grid (1..1000) dialog will appear. Enter a value to be used for the Step X property of the default Global Board Snap Grid and click OK - the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you enter a snap grid setting without specifying units, the entry will be in the default measurement units employed for the design. Specifying units when entering the value (mil or mm) will change the default measurement units for the document to those specified, if not currently the default.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 1Mil

Applied Parameters: Axis=Y|Value=1Mil

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 1mil. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 1 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 1 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 1mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 5Mil

Applied Parameters: Axis=Y|Value=5Mil

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 5mil. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 5 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 5 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 5mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 10Mil

Applied Parameters: Axis=Y|Value=10Mil

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 10mil. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 10 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 10 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 10mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 20Mil

Applied Parameters: Axis=Y|Value=20Mil

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 20mil. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 20 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 20 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 20mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 25Mil

Applied Parameters: Axis=Y|Value=25Mil

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 25mil. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 25 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 25 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 25mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 50Mil

Applied Parameters: Axis=Y|Value=50Mil

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 50mil. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 50 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 50 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 50mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 100Mil

Applied Parameters: Axis=Y|Value=100Mil

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 100mil. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 100 Mil command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 100 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 100mil, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using metric units for your board, the equivalent converted value in mm will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 0.025mm

Applied Parameters: Axis=Y|Value=0.025MM

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 0.025mm. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 0.025 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 0.025 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 0.025mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 0.100mm

Applied Parameters: Axis=Y|Value=0.100MM

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 0.100mm. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 0.100 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 0.100 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 0.100mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 0.250mm

Applied Parameters: Axis=Y|Value=0.250MM

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 0.250mm. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 0.250 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 0.250 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 0.2500mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 0.500mm

Applied Parameters: Axis=Y|Value=0.500MM

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 0.500mm. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 0.500 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 0.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 0.500mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 1.000mm

Applied Parameters: Axis=Y|Value=1.000MM

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 1.000mm. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 1.000 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 1.000 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 1.000mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y to 2.500mm

Applied Parameters: Axis=Y|Value=2.500MM

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to 2.500mm. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » 2.500 mm command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » 2.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for the Step Y property of the default Global Board Snap Grid will be set to 2.500mm, and the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you are currently using imperial units for your board, the equivalent converted value in mils will be used.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Set Snap Grid Y

Applied Parameters: Axis=Y

Summary

This command is used to set the Y (vertical) step value - for the default Global Board Snap Grid - to a chosen value. This value, together with the X (horizontal) step value, defines the Snap Grid for manual movement and placement in the current document. The cursor automatically snaps to this grid, positioning the reference point of the object being placed onto the nearest grid location.

Access

This command is accessed from the PCB Editor, and PCB Library Editor, by:

Using the G keyboard shortcut, then choosing the Snap Grid Y » Set Snap Grid command from the pop-up menu.
PCB Editor - choosing the Snap Grid Y » Set Snap Grid entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the Snap Grid (1..1000) dialog will appear. Enter a value to be used for the Step Y property of the default Global Board Snap Grid and click OK - the grid will update accordingly in the workspace.

Tips

This command only affects the default snap grid for the board, and not any custom grids (cartesian and polar) that you may have defined.
If the Step X and Step Y properties were previously linked, this command will unlink the two.
If you enter a snap grid setting without specifying units, the entry will be in the default measurement units employed for the design. Specifying units when entering the value (mil or mm) will change the default measurement units for the document to those specified, if not currently the default.
The step values can be changed as required for the default snap grid, by editing the grid through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace). Double-click the entry for the Global Board Snap Grid (or select and click the Properties button), and in the subsequent Cartesian Grid Editor dialog, make changes to the properties in the Steps region.

Версия для печати

If you find an issue, select the text/image and pressCtrl + Enterto send us your feedback.

Примечание

Набор доступных функций зависит от вашего уровня доступа к продуктам Altium. Ознакомьтесь с функциями, включенными в различные уровни Подписки на ПО Altium, и функциональными возможностями приложений, предоставляемых платформой Altium 365.

Если вы не видите в своем ПО функцию, описанную здесь, свяжитесь с отделом продаж Altium, чтобы узнать больше.