Working with a Part Object on a Schematic Sheet in Altium NEXUS

This documentation page references Altium NEXUS/NEXUS Client (part of the deployed NEXUS solution), which has been discontinued. All your PCB design, data management and collaboration needs can now be delivered by Altium Designer and a connected Altium 365 Workspace. Check out the FAQs page for more information.

 

Parent page: Schematic Objects

 The Part represents the actual physical electronic component. The Part represents the actual physical electronic component.

Summary

A part is an electrical design primitive. It is a schematic symbol that represents an electronic device, such as a resistor, a switch, an operational amplifier, a voltage regulator, etc. Parts are stored within components in schematic component libraries. Note that each component can contain one or more parts. Along with a symbolic representation of the component, the part also includes links to models, such as the PCB footprint, and also parameters that are used to document details such as component parameters and supplier information. How the model links and parameters are added to the part depends on the type of library storage being used.

The terms Part and Component are both used to describe the symbol that represents the actual electronic device. The term Part is used because some components contain multiple parts. For example, a quad Op Amp component contains four separate Op Amps, or a resistor network can contain eight independent resistors. For these types of devices, you can create a separate schematic symbol to represent each Part during the component definition and place each of these parts independently. The terms Part and Component are used interchangeably on this page unless a multi-part component is being discussed.

Availability

Parts are available for placement in both the schematic and schematic library editors.

  • In the schematic editor, click Place » Part.
  • From the Libraries panel, click Place <ComponentName>
In order to access the Libraries panel, enable the Value option in the Advanced Settings dialog for the following Preference NamesLegacy.UnmanagedLibraries and Legacy.LibraryPanel​.
  • From the SCH Library panel when in the schematic library editor, click Place

Placement

The way in which a part is placed on a schematic sheet depends on how and from where placement mode is invoked.

Schematic components (and PCB component footprints) can only be placed from Available Libraries. The term Available Libraries includes libraries that are part of the current project being worked on or libraries currently installed in Altium NEXUS. The currently available libraries are listed in the Libraries panel. Libraries can be installed and removed through the Data Management - Installed Libraries page of the Preferences dialog or the Available Libraries dialog (click Libraries on the Libraries panel).

Placing from the Libraries Panel

In the schematic editor, the part selection and placement process is done from the Libraries panel.

  • The panel displays the contents of the currently selected library. Use the drop-down next to the library name to choose another library.
  • Use the mask field below the currently selected library field to filter the list and speed the searching process or scroll and select the required part.
  • Click Libraries to open the Available Libraries dialog and add or remove libraries.
  • Click Search to open the Libraries Search dialog and search for a part.
  • Click Place, double-click, or click and drag to place the selected component onto the active schematic sheet. While the part is floating on the cursor, it can be rotated (press Spacebar), mirrored along an axis (press X or Y), or edited (press Tab) before placement.
  • The columns shown in the list of components in the currently selected library can be reorganized (click and drag) or reconfigured (right-click then choose Select Columns).

Searching for a Component

If you cannot locate the required part in the Libraries panel, use the Search feature. To do this, click Search to open the Libraries Search dialog.

  • The default search Scope is to search for Components in the Available Libraries.
  • Alternatively, the dialog also supports searching through Libraries on path stored in folders on a drive. To do this, enable the Libraries on path option then configure the Path options as required.
  • The Filters use "AND" and, therefore, it is better to start with a simple filter and if there are many results, use the Refine last search mode to search within the results.
  • Search results are presented in the Libraries panel under Query Results. Re-select a component library to return to browsing in the panel.

.

Placing from the Schematic Library Editor

A part also can be placed directly from a library that is open in the schematic library editor from the SCH Library panel. Note that:

  • Clicking the Place button in the panel will place the selected part (component) in the last active schematic sheet.
  • While the part is floating on the cursor, it can be rotated (press Spacebar), mirrored along an axis (press X or Y), or edited (press Tab) before placement.
  • If a part is placed directly from a library, that library does not need to be added in the Available Libraries dialog first.

 A Part can also be placed directly from an open Schematic Library using the SCH Library panel. A Part can also be placed directly from an open Schematic Library using the SCH Library panel.

While attributes can be modified during placement (Tab to access the Properties panel), keep in mind that these will become the default settings for further placement unless the Permanent option on the Schematic – Defaults page of the Preferences dialog is enabled. When this option is enabled, changes made will affect only the object being placed and subsequent objects placed during the same placement session.

Placing from the Explorer Panel

In the schematic editor, the part selection and placement process is done from the Explorer panel. Click Place » Part to open the Explorer panel. Navigate to the desired part, right-click on the part then select Place. The selected part appears on the workspace with a crosshair. Click or Enter to place it.

Graphical Editing

Graphical editing for a part is limited to moving, rotating and mirroring. When a part is selected in the workspace, a dashed selection box will appear around it. To graphically manipulate a selected component:

  • Press Delete to remove the selected part from the design.
  • Click and hold to move the selected part. The cursor will jump to the nearest electrical hotspot (the wiring end of the nearest pin).
  • While a part is moving on the cursor, press the Spacebar to rotate it counterclockwise (Shift+Spacebar to rotate it clockwise). Rotation is in 90° increments.
  • While a part is moving on the cursor, press the X or Y key to mirror it along that axis.

A selected PartA selected Part

When a component is rotated, its text strings are automatically repositioned to suit the new orientation. This behavior can be disabled if required. To do this, edit the string then clear the Autoposition checkbox in the Properties panel. Note that manually positioned text strings are denoted by a dot. These dots can be hidden if required by clearing the Mark Manual Parameters option on the Schematic - Graphical Editing page of the Preferences dialog.

If attempting to graphically modify an object that has its Locked property enabled, a dialog will appear asking for confirmation to proceed with the edit. If the Protect Locked Objects option is enabled on the Schematic - Graphical Editing page of the Preferences dialog and the Locked option for that design object is enabled as well, then that object cannot be selected or graphically edited. Double-click on the locked object directly and disable the Locked property or disable the Protect Locked Objects option to graphically edit the object.

Working Between the Schematic Component and the PCB Component

The software includes tools to help work between the component on the schematic and that same component on the PCB. These tools include Cross Probing, Cross Selection, and Selecting the PCB Components from the schematic.

Cross Probe

As the name implies, Cross Probe allows you to click on a component in one editor and jump to that component in the other editor. To Cross Probe:

  • Click Cross Probe located on the schematic or PCB editor menu on the Tools menu.
  • When you click the component in the schematic editor, it will be centered and zoomed in the PCB editor. The zoom level is set on the System - Navigation page of the Preferences dialog.
  • The default behavior is to remain in the same editor, ready to cross probe another component. To switch to the other editor as you Cross Probe, hold the Ctrl key. 

Cross Select Mode

Cross Select Mode selects the same component in the other editor. Note that it does not zoom and center. Cross Selection is either on or off. Click Tools » Cross Select Mode to toggle the mode on/off. Select multiple components by holding the Shift key as you click to select.​

Selecting the PCB Components

This feature allows you to select multiple schematic components in a specific order, then place those same components in the PCB editor in the same order. To use this feature:

  • Select the components on the schematic one by one (hold Shift as you click to select multiple components).
  • Switch to the PCB editor then press the I, C shortcut to launch the Reposition Selected Components command. The Reposition Selected Components command is also available on the right-click menu after pressing the I shortcut. 
If attempting to graphically modify an object that has its Locked property enabled, a dialog will appear asking for confirmation to proceed with the edit. If the Protect Locked Objects option is enabled on the Schematic – Graphical Editing page of the Preferences dialog, and the Locked option for that design object is enabled as well, then that object cannot be selected or graphically edited. Click the locked object to select it then disable the Locked property in the List panel or disable the Protect Locked Objects option to graphically edit the object.

Non-Graphical Editing

Via the Properties Panel

Properties page: Part Properties

This method of editing uses the associated Properties panel mode to modify the properties of a part object.

The Component mode of the Properties panelThe Component mode of the Properties panel

During placement, the Component mode of the Properties panel can be accessed by pressing the Tab key.

After placement, the Component mode of the Properties panel can be accessed in one of the following ways:

  • Double-click on the placed component line.
  • Place the cursor over the component, right-click then choose Properties from the context menu.
  • If the Properties panel is already active, select the component.

Editing Multiple Objects

The Properties panel supports multiple object editing, where the property settings that are identical in all currently selected objects may be modified. When multiples of the same object type are selected manually, via the Find Similar Objects dialog or through a Filter or List panel, a Properties panel field entry that is not shown as an asterisk (*) may be edited for all selected objects.

Via a List Panel

Panel pages: SCH List, SCHLIB List, SCH Filter, SCHLIB Filter

List panel allows you to display design objects from one or more documents in tabular format enabling quick inspection and modification of object attributes. Used in conjunction with appropriate filtering - by using the applicable Filter panel, or the Find Similar Objects dialog - it enables the display of just those objects falling under the scope of the active filter – allowing you to target and edit multiple design objects with greater accuracy and efficiency.

If you find an issue, select the text/image and pressCtrl + Enterto send us your feedback.
콘텐츠