DocumentPreferences

Applied Parameters: VisibleGridKind=Toggle

Summary

This command is used to toggle the markers used for the fine-level display of the default Global Board Snap Grid between lines and dots.

Access

This command can be accessed from both PCB and PCB Library Editors:

• PCB Editor - the following methods of access are available:
  • Choose the View » Grids » Toggle Visible Grid Kind command from the main menus.
  • Choose the Toggle Visible Grid Kind entry on the Grids drop-down () of the Utilities toolbar.
  • Use the V keyboard shortcut then choose the Grids » Toggle Visible Grid Kind entry on the subsequent pop-up menu.
• PCB Library Editor - the following method of access is available:
  • Choose the View » Grids » Toggle Visible Grid Kind command from the main menus.
  • Choose the Toggle Visible Grid Kind entry on the Grids drop-down () of the PCB Lib Standard toolbar.
  • Use the V keyboard shortcut then choose the Grids » Toggle Visible Grid Kind entry on the subsequent pop-up menu.

Use

After launching the command, the marker type used for the Global Board Snap Grid's fine-level grid display will change to either dots or lines depending on the type that was previously in use.

Tips

1. This command only toggles the marker type used for the fine-level display and not the coarse-level display.
2. The marker type can also be changed through the Cartesian Grid Editor dialog when editing the default Global Board Snap Grid. Grid management is performed through the Grid Manager section of the Properties panel when no objects are currently selected in the design workspace.

Applied Parameters: ElectricalGridEnabled = Toggle

Summary

This command is used to cycle to the next mode of object Hotspot Snapping. Often referred to as an Electrical Grid, object hotspot snapping provides an aid to routing electrical objects, especially those that may not fall on the default Global Board Snap Grid or a defined custom grid. It gives you a distance, or tolerance, in which the cursor can be away from an object but still snap to the object's hot-spot (e.g., the center of a pad). Object hotspot snapping overrides a snap grid allowing you to easily connect to an off-grid object.

Access

This command can be accessed from both PCB and PCB Library Editors by:

• Choosing the View » Grids » Toggle Object Hotspot Snapping command from the main menus.
• Using the Shift+E keyboard shortcut.
• Using the V keyboard shortcut then choose the Grids » Toggle Object Hotspot Snapping entry on the subsequent pop-up menu.

In addition, from the PCB Editor, you can choose the Toggle Object Hotspot Snapping entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, object hotspot snapping will cycle to the next mode within the following modes depending on its previous state:

• ON (Current Layer) - hotspot snap is enabled for the current layer. That is, the cursor will snap to object hotspots on the current layer only.
• ON (All Layers) - hotspot snap is enabled for all visible layers. That is, the cursor will snap to object hotspots on any layer, not just the current layer.
• OFF - hotspot snap is disabled.

Tips

1. Hotspot snapping can also be enabled/disabled and its range (Snap Distance) defined in the Snap Options section of the Properties panel (when no objects are currently selected in the design workspace).
2. Hold the Ctrl shortcut key to temporarily disable object hotspot snapping during interactive routing.

Applied Parameters: MeasurementUnit=Toggle

Summary

This command is used to toggle the measurement units for the current document, between metric (mm) and imperial (mil).

Access

This command can be accessed from the PCB Editor, and PCB Library Editor, by:

• Choosing the View » Toggle Units command from the main menus.
• Using the Q keyboard shortcut.
• Using the V keyboard shortcut then choosing the Toggle Units entry on the subsequent pop-up menu.

Use

After launching the command, the measurement units for the current document will become either metric or imperial depending on the measurement units previously in force.

Tips

1. The current measurement units for the document can be checked/changed in the Other section of the Properties panel (when no objects are currently selected in the design workspace).

Applied Parameters: MaskLevel=Increase

Summary

This command is used to increase the masking level, and therefore, decrease the extent of dimming in the workspace for all objects not falling under the scope of a currently applied filter.

Access

This command can be accessed from the PCB Editor by:

• Choosing the View » Increase Mask Level command from the main menus.
• Using the ] keyboard shortcut.

Use

After launching the command, the level or intensity of masking applied in the workspace will be decreased. Design objects that do not fall under the scope of the currently applied filter will become less faded. Continue using this command to further increase the display intensity of objects not belonging to the filtered set.

Tips

1. Use of this command corresponds to sliding the Dimmed Objects slider to the right (increasing its value). This slider can be found in the Mask and Dim Settings section on the View Options tab of the View Configuration panel.

Applied Parameters: MaskLevel=Decrease

Summary

This command is used to decrease the masking level, and therefore, increase the extent of dimming in the workspace for all objects not falling under the scope of a currently applied filter.

Access

This command can be accessed from the PCB Editor by:

• Choosing the View » Decrease Mask Level command from the main menus.
• Using the [ keyboard shortcut.

Use

After launching the command, the level or intensity of masking applied in the workspace will be increased. Design objects that do not fall under the scope of the currently applied filter will become more faded. Continue using this command to further decrease the display intensity of objects not belonging to the filtered set.

Tips

1. Use of this command corresponds to sliding the Dimmed Objects slider to the left (decreasing its value). This slider can be found in the Mask and Dim Settings section on the View Options tab of the View Configuration panel.