Analyzing Your Design Using Circuit Simulation

The Mixed Simulation capabilities are available through an Altium Designer Mixed Simulation system extension, which is installed with Altium Designer by default. The extension can be manually installed/removed or updated from the Altium Designer Extensions and Updates page (select the Extensions and Updates option from the Current User control menu – ).

1. Select the File » New » Project command from the main menus.

2. The Create Project dialog will open:

   1. In the Locations list, select the entry for your Workspace (or the Local Projects entry if you are not using a Workspace).
   2. In the Project Type list, choose the <Empty> entry under the PCB type.
   3. Enter Filter in the Project Name field.
   4. Set other options on the right-hand side of the dialog as required (e.g., the storage folder) and click the Create button.

   A new project will be created, and the project entry will appear in the Projects panel.

   

3. Right-click the project entry in the Projects panel and select the Add New to Project » Schematic command from the context menu.

   

4. A blank sheet of a new schematic document will appear. Save it on your hard drive by right-clicking its entry in the Projects panel and selecting the Save As command from the context menu. The Save As dialog will open, ready to save the document in the same location as the project file. Type Filter in the File name field and click Save (there is no need to type in the extension, as it will be added automatically).
5. Since you added a new document to the project, the project file has changed. Right-click on the project entry in the Projects panel, then select Save to save the project changes.

The filter circuit to be simulated is shown below. In this section, we will locate the required components, set up their component properties and then wire the schematic.

Schematic of the filter circuit

Placing Simulation-Ready Components

1. Components for the schematic will be sourced from the Simulation Generic Components library provided with an Altium Designer installation by default:

   1. Open the Components panel by clicking the Panels button at the bottom-right of the design space and selecting Components from the menu that appears.

      

   2. Select the Simulation Generic Components library from the drop-down at the top of the panel (if the panel is in its compact mode) or from the Categories pane access by clicking the  button at the top-left of the panel (if the panel is in its normal mode). The list of components the library provides will be presented in the panel.

      

2. Place the operational amplifier:

   1. In the component list, find the OpAmp with power terminals component, right-click its entry and select the Place command from the main menus. The component will appear attached to the cursor in the design space but do not place the component yet.

      

      You can use the Component panel's Search field to quickly find the component required.
   2. While the op amp is floating on the cursor, press the Tab key to open the Properties panel, where you can edit its properties before placing the component on the schematic.

   3. In the General region of the Properties panel, change the Designator to U1.

      

   4. Click the Pause button ( ) in the design space to return to component placement.
   5. Click in the design space to place an instance of the op amp.
   6. You will stay in component placement mode to place further component instances. Since only one instance of the op amp component is required for this circuit, right-click to exit component placement mode.

3. Place resistors:

   1. In the Components panel, find the Resistor component, right-click its entry and select the Place command from the main menus.
   2. While the resistor is floating on the cursor, press the Tab key.
   3. Change the component properties in the Properties panel that opens as follows:
      • In the General region, change the Designator to R1.
      • In the Parameters region, change the Value of the Value parameter to 100K.

      

   4. Click the Pause button ( ) in the design space to return to component placement.

   5. Click in the design space to place an instance of the resistor.

      

   6. Move the cursor and click in the design space to place another instance of the resistor with the same value. The designator of the new instance will be incremented automatically (R2).

      

   7. Right-click to exit component placement mode.

4. Place capacitors:

   1. In the Components panel, find the Capacitor component, right-click its entry and select the Place command from the main menus.
   2. While the capacitor is floating on the cursor, press the Tab key.
   3. Change the component properties in the Properties panel that opens as follows:
      • In the General region, change the Designator to C1.
      • In the Parameters region, change the Value of the Value parameter to 112p.

      

   4. Click the Pause button ( ) in the design space to return to component placement.

   5. Click in the design space to place an instance of the capacitor.

      

   6. While the capacitor is still floating on the cursor, ready to place another instance of the capacitor, press the Tab key.
   7. In the Parameters region of the Properties panel, change the Value of the Value parameter to 56p.
   8. Click the Pause button ( ) in the design space to return to component placement.
   9. Press the Spacebar to rotate the component in 90° increments until it has the correct orientation.

   10. Move the cursor and click in the design space to place another instance of the capacitor. The designator of the new instance will be incremented automatically (C2).

       

   11. Right-click to exit component placement mode.

Adding the Voltage Sources

To power the circuit when simulating, voltage sources are needed.

1. Place the VDD voltage source:

   1. Select the Simulate » Place Sources » Voltage Source command from the main menus.
   2. While the voltage source is floating on the cursor, press the Tab key.
   3. Change the source properties in the Properties panel that opens as follows:
      • In the General region, change the Designator to VDD and select DC Source as the source's Stimulus Type.

      • In the Parameters region, change parameter values as follows:

        DC Magnitude = 5
AC Magnitude = 0
AC Phase = 0

      

   4. Click the Pause button ( ) in the design space to return to voltage source placement.

   5. Click in the design space to place an instance of the voltage source.

      

2. Place the VSS voltage source:

   1. While the voltage source is still floating on the cursor, ready to place another instance of the source, press the Tab key.
   2. Change the source properties in the Properties panel that opens as follows:
      • In the General region, change the Designator to VSS and select DC Source as the source's Stimulus Type.

      • In the Parameters region, change parameter values as follows:

        DC Magnitude = -5
AC Magnitude = 0
AC Phase = 0

      

   3. Click the Pause button ( ) in the design space to return to voltage source placement.

   4. Move the cursor and click in the design space to place another instance of the voltage source.

      

3. Place the sinusoidal voltage source:

   1. While the voltage source is still floating on the cursor, ready to place another instance of the source, press the Tab key.
   2. Change the source properties in the Properties panel that opens as follows:
      • In the General region of the Properties panel, change the Designator to VIN and select Sinusoidal as the source's Stimulus Type.

      • In the Parameters region of the Properties panel, change parameter values as follows:

        DC Magnitude = 0
AC Magnitude = 1
AC Phase = 0
Offset = 0
Amplitude = 5
Frequency = 50K
Delay = 0
Dampling Factor = 0
Phase = 0

      

   3. Click the Pause button ( ) in the design space to return to voltage source placement.

   4. Move the cursor and click in the design space to place another instance of the voltage source.

      

   5. Right-click to exit component placement mode.

Wiring Up the Circuit

Wiring is the process of creating connectivity between the various components of your circuit. In this section, the circuit will be wired up according to the image below.

1. Select the Place » Wire command from the main menus.
2. Position the cursor over the hotspot of the "+" pin of the op amp – a red connection marker (red cross) will appear at the cursor location. This indicates that the cursor is over a valid electrical connection point on the component.
3. Click to anchor the starting point for the wire.
4. Position the cursor over the hotspot of the nearest pin of R2 until you see the cursor change to a red connection marker.
5. Click to connect the wire to the pin. The cursor will release from that wire.
6. Wire up the rest of your circuit, as shown in the video below.
7. When you have finished placing all the wires, right-click to exit placement mode.

Adding Power Ports

1. Place GND power ports:

   1. Select the Place » Power Port command from the main menus.
   2. While the power port is floating on the cursor, press the Tab key.

   3. In the Properties region of the Properties panel, set Name = GND and Style = Power Ground.

      

   4. Click the Pause button ( ) in the design space to return to power port placement.

   5. Place three power ports, one on each of the "-" pins of the voltage source components, as shown in the image below.

      If required, rotate the floating power port by pressing the Spacebar.

      

2. Place VDD power ports:

   1. While the power port is floating on the cursor, press the Tab key and set Name = VDD and Style = Bar in the Properties panel.
   2. Click the Pause button ( ) in the design space to return to power port placement.

   3. Place two power ports, as shown in the image below.

      

3. Place VSS power ports:

   1. While the power port is floating on the cursor, press the Tab key and set Name = VSS and Style = Bar in the Properties panel.
   2. Click the Pause button ( ) in the design space to return to power port placement.

   3. Place three power ports, as shown in the image below.

      

   4. Right-click to exit placement mode.

Adding Net Labels

1. Place a net label for the input net:

   1. Select the Place » Net Label command from the main menus.

   2. While the power port is floating on the cursor, press the Tab key and set Net Name = IN.

      

   3. Click the Pause button ( ) in the design space to return to net label placement.

   4. Click to place the net label on the wire between VIN and R1. Note that the bottom left corner of the net label is its hotspot – this point must touch the wire.

      

2. Place a net label for the output net:

   1. While the power port is floating on the cursor, press the Tab key and set Net Name = OUT.

   2. Click to place the net label on the wire exiting the output pin of the op amp.

      

   3. Right-click to exit placement mode.
3. Save the schematic document by right-clicking its entry in the Projects panel and selecting Save from the context menu.

Altium Designer allows you to run circuit simulations directly from the schematic. The simulations are configured and driven from the Simulation Dashboard panel.

1. Open the Simulation Dashboard panel by clicking the Panels button at the bottom-right of the design space and selecting Simulation Dashboard from the menu that appears.

2. Expand the Verification collapsible region of the panel and click the Start Verification button. A green check should appear for both Electrical Rule Check and Simulation Models entries in the region.

   

3. If any violations are detected, find and fix violation conditions to continue.

4. Expand the Preparation collapsible region of the panel and make sure that all three voltage sources added to the schematic are shown in the Simulation Sources list and enabled.

   

Setting Up a Transient Analysis

A transient analysis generates output like that normally shown on an oscilloscope, computing the transient output variables (voltage, current, or power) as a function of time over the user-specified time interval.

1. Expand the Analysis Setup & Run collapsible region of the Simulation Dashboard panel and the Transient region therein.

   

2. Make sure that the Interval option is selected () and enter the following values:
   • From = 0
   • To = 60u
   • Step = 100n

   

3. Add a new expression for the input signal. This expression will be outputted as a waveform in the simulation result document:

   1. Click the Add control under the Output Expressions header to add a field for a new expression to be outputted as a waveform in the simulation result document.

      

   2. Click the  button at the right of the added field to access the Add Output Expression dialog, where the output expression can be configured.

      

   3. In the Add Output Expression dialog, select Node Voltages from the drop-down in the Waveform region and click the v(IN) entry in the list below. The v(IN) expression will be added to the Expression Y field of the dialog.

   4. Click Create in the Add Output Expression dialog. The expression will appear in the Simulation Dashboard panel.

      

4. Add an output expression for the output signal:

   1. Click the Add control in the Simulation Dashboard panel to add a field for another output expression and then the  button at the right of the added field.
   2. In the Add Output Expression dialog, select Node Voltages from the drop-down in the Waveform region and click the v(OUT) entry in the list below.

   3. Select New Plot in the Plot Number drop-down to draw the waveform for this expression in another plot in the simulation result document. After selecting, the drop-down will show 2.

      

   4. Click Create in the Add Output Expression dialog to add the expression to the Simulation Dashboard panel.

5. At this point, the transient analysis is configured. Its options should look in the Simulation Dashboard panel as shown below.

   

Setting Up an AC Sweep Analysis

An AC sweep analysis generates output that shows the frequency response of the circuit, calculating the small-signal AC output variables as a function of frequency. The desired output of an AC small-signal analysis is usually a transfer function, e.g., voltage gain.

1. In the Simulation Dashboard panel, expand the AC Sweep region within the Analysis Setup & Run collapsible region.
2. Select Decade as the sweep Type and enter the following values:
   • Start Frequency = 100m
   • End Frequency = 1meg
   • Points/Dec = 100

   

3. Add an output expression for the magnitude in decibels of the input signal:

   1. Click the Add control under the Output Expressions header to add a field for a new expression and then the  button at the right of the added field.
   2. In the Add Output Expression dialog, select Node Voltages from the drop-down in the Waveform region and click the v(IN) entry in the list below.
   3. Select Magnitude (dB) from the Complex Functions drop-down in the Add Output Expression dialog and click Create.

   

4. Add an output expression for the magnitude in decibels of the output signal:

   1. Click the Add control under the Output Expressions header to add a field for a new expression and then the  button at the right of the added field.
   2. In the Add Output Expression dialog, select Node Voltages from the drop-down in the Waveform region and click the v(OUT) entry in the list below.
   3. Select Magnitude (dB) from the Complex Functions drop-down in the Add Output Expression dialog and click Create.

5. Add an output expression for the phase in degrees of the input signal:

   1. Click the Add control in the Simulation Dashboard panel to add a field for another output expression and the  button at the right of the added field.
   2. In the Add Output Expression dialog, select Node Voltages from the drop-down in the Waveform region and click the v(IN) entry in the list below.
   3. Select Phase (Deg) from the Complex Functions drop-down in the Add Output Expression dialog.
   4. Select New Plot in the Plot Number drop-down and then click Create in the Add Output Expression dialog.

   

6. Add an output expression for the phase in degrees of the output signal:

   1. Click the Add control in the Simulation Dashboard panel to add a field for another output expression and the  button at the right of the added field.
   2. In the Add Output Expression dialog, select Node Voltages from the drop-down in the Waveform region and click the v(OUT) entry in the list below.
   3. Select Phase (Deg) from the Complex Functions drop-down in the Add Output Expression dialog.

7. At this point, the AC sweep analysis is configured. Its options should be in the Simulation Dashboard panel as shown below.

   

8. The simulation configuration file (project_sim_config.simcfg) will appear in the Settings\Simulation Documents folder of the project structure in the Projects panel. Save the document by right-clicking its entry in the Projects panel and selecting the Save As command from the context menu.

   

   The Save As dialog will open, ready to save the document in the project folder on your hard drive. Click Save to save the document in this default location with the default name.

9. Save the project file by right-clicking its entry in the Projects panel and selecting the Save command from the context menu.

1. Click the Run button at the right of the Transient region header in the Simulation Dashboard panel to perform the transient analysis.

   

2. When the simulation succeeds, the Messages panel will report about successfully completed simulation. It can be closed.

3. A new simulation result document named Filter.sdf will automatically open in the SimData editor as a document tab. It contains a single Transient Analysis chart (indicated by a tab at the bottom of the document), with two plots, each containing a single waveform, v(IN) and v(OUT), respectively.

   

4. Switch to the schematic document by clicking its tab at the top of the design space.

5. Click the Run button at the right of the AC Sweep region header in the Simulation Dashboard panel to perform the AC sweep analysis.

   

6. Close the Messages panel.

7. The simulation result document containing a single AC Analysis chart will open. The chart includes two plots, with two waveforms in each.

   

8. Determine the 3dB point using the measurement cursors:

   1. Right-click on the dB(v(OUT)) wave and select Cursor A.

   2. Position cursor A in the lowpass section by dragging the marker (the location is not critical, as long as it is in the lowpass region).

      

   3. Right-click on the dB(v(OUT)) wave again and select Cursor B.
   4. The Sim Data panel will be used to help locate the cursor (if the panel is not visible, click the Panels button at the bottom-right of the design space and select Sim Data from the menu that appears to display it).
   5. While watching the B-A Measurement value in the Measurement Cursors region of the Sim Data panel, click and drag Cursor B to give a Y (gain) value of -3.

   6. It can be seen that the X result for Wave Name B is appr. 20k, indicating that the 3dB point of the filter circuit is 20kHz.

      

   7. To clear the cursors, right-click on each cursor marker and select Cursor Off.
   8. To clear filtering in the document, click the Clear button at the bottom-right of the design space.

9. The simulation result document (Filter.sdf) will appear in the Generated\Simulation Documents folder of the project structure in the Projects panel. Save the document by right-clicking its entry in the Projects panel and selecting the Save As command from the context menu.

   

   The Save As dialog will open, ready to save the document in the Simulation subfolder of the project folder on your hard drive. Click Save to save the document in this default location with the default name.

10. Switch to the schematic document by clicking its tab at the top of the design space.

11. In the Simulation Dashboard panel, expand the Results collapsible region. The region will contain the list of performed simulation runs (Transient Analysis and AC Analysis in this example).

    

12. To show the results of the transient analysis run previously, click the  button at the right of the Transient Analysis entry and select Show Results.

    

    The simulation result document will open to show the results of the transient analysis.

13. Save modified project documents and the project itself by right-clicking their entries in the Projects panel and selecting the Save command from the context menu.
14. If you created the project in your connected Workspace, right-click the project entry in the Projects panel and select the Save to Server command from the context menu and then click OK in the Save to Server dialog that opens.