Applied Parameters: None
Summary
This command is used to place a Wire object onto the active document. A wire is a polyline electrical design primitive that is used to form electrical connections between points on a schematic. It is analogous to a physical wire.
For detailed information about this object type, see
Wire.
Access
Wires are available for placement in the Schematic Editor only, by:
- Choosing Place » Wire from the main menus.
- Locating and using the Wire command (
) on the Active Bar.
If the command has been recently used from the Active Bar, it will become the active/visible button. Where other commands are available, this is indicated by a triangle at the bottom-right corner of the button. Click and hold on the active button to access a menu of all associated commands for that grouping.
- Clicking the
button on the Wiring toolbar.
- Using the Ctrl+W keyboard shortcut.
- Right-clicking and choosing Place » Wire from the context menu.
Use
After launching the command, the cursor will change to a cross-hair and you will enter wire placement mode. Placement is made by performing the following sequence of actions:
- Click or press Enter to anchor the starting point for the wire.
- Position the cursor and click or press Enter to anchor a series of vertex points that define the shape of the wire.
- After placing the final vertex point, right-click or press Esc to complete placement of the wire.
- Continue placing further wire objects, or right-click or press Esc to exit placement mode.
- Use the Backspace or Delete keys to remove the last wire segment placed.
At any time during placement, press the Tab key to access the Properties panel, from where properties for the wire can be changed on-the-fly. Pressing Tab pauses placement, allowing you to interact with the panel (or other area of the software) directly. To resume, click the pause symbol that appears over the workspace.
Placement Modes
When placing a wire there are 3 'manual' placement modes, 2 of which have Start and End sub-modes. The mode specifies how corners are created when placing wires and the angles at which wires can be placed. During placement:
- Press Shift+Spacebar to cycle through the 90 Degree, 45 Degree and Any Angle modes.
- While in the 90 Degree or 45 Degree mode (known as true orthogonal modes), press Spacebar to cycle between the Start and End sub-modes.
- During placement, the current placement mode is displayed in the Status bar. You can change modes at any time during wire placement.
- In modes other than Any Angle, the line segment attached to the cursor is a look ahead segment. The segment you are actually placing precedes this look ahead segment.
45 degree mode
90 degree mode
Any angle mode
Press Shift+Spacebar to cycle through the different placement modes.
There is also an Auto Wire mode, which can be used to route quickly from the previous segment end, to the point where the cursor is clicked, using the Point to Point Router. The path of the route will be the most efficient possible, while avoiding existing placed objects on the sheet.
Guided Wiring
Schematics have a definable 'electrical grid' that makes it easy to define electrical connections between objects. As you are placing a wire, when the wire falls within a defined range of attraction of another electrical object the cursor will snap to the fixed object and a Hot Spot (red cross) will appear.
![Hot Spot (red cross). Hot Spot (red cross).](/documentation/sites/default/files/wiki_attachments/295204/Sch_Obj-Wire_GuidedWiring.webp)
Hot Spot (red cross).
The Hot Spot guides you to where a valid connection can be made and automatically snaps the cursor to electrical connection points.
The range of attraction, or distance within which an object will electrically snap to the hotspot of another electrical object, can be defined using the
Snap Distance field, in the
General section of the
Properties panel (when no objects are selected on the sheet). It is recommended that you set this 'object snapping' range to be slightly smaller than the current snap grid, or it becomes difficult to position electrical objects one snap grid apart. Object snapping can be toggled on or off using the
Shift+E keyboard shortcut, or by enabling/disabling the
Snap option (above the
Snap Distance field in the
Properties panel).
Tips
- For information on how a placed wire object can be modified graphically, directly in the workspace, see Graphical Editing.
- A T-junction in a wire is automatically connected by a junction (Compiler-Generated Juntion). If the Break Wires At Autojunctions option is enabled, on the Schematic - General page of the Preferences dialog, an existing wire segment will be broken into two at the point where an autojunction is inserted. For example, when making a T-Junction, the perpendicular wire segment will be broken into two segments, one each side of the junction. With this option disabled, the wire segment will remain unbroken at the junction.
- While attributes can be modified during placement (Tab to bring up the Properties panel), bear in mind that these will become the default settings for further placement unless the Permanent option on the Schematic - Defaults page of the Preferences dialog is enabled. When this option is enabled, changes made will affect only the object being placed and subsequent objects placed during the same placement session.