Swapping Pins, Pairs and Parts in a Design in Altium NEXUS
Working in harmony with Altium NEXUS's interactive routing and BGA escape routing capabilities is the pin, differential pair and part swapping system. This feature provides all the benefits of traditional pin-swapping systems, but takes advantage of Altium NEXUS's intimate understanding of the net assignments in the design. During a pin swap operation Altium NEXUS analyses the net assigned to the chosen pin, and dynamically reassigns the net on the pin and any connected copper.
This level of functionality means that partially routed nets and pre-routed multilayer escapes from complex BGA devices can be swapped. Differential pairs can also be swapped, taking advantage of the knowledge about differential pin-pairs on FPGAs.
At the PCB level the system includes a powerful automatic optimizer that uses this information to dynamically re-assign nets to improve routability. For example, the system can perform a reconnect on multiple devices that have been escape routed on multiple layers. It will assign these based on matching escape route layers, shortest Manhattan routing distance, and minimum number of crossovers on each layer.
The addition of partial routed net swapping, along with the automatic optimizer gives you the ability to adopt a hierarchical and iterative routing strategy, escape routing devices first, then routing to the edge of a given area, and then finally connecting these sections together. At any time, the automatic swapper can be re-run to re-optimize, based on the updated information provided by the partially routed nets.
There are three categories of swapping:
- Pin Swapping
- Differential Pair Swapping
- Sub-part Swapping.
Configuring Swap Groups
For each category of swapping swap groups dictate what can be and what can not be swapped within a component. In the case of pin swapping, pins within a component that share a common pin group are able to be swapped with one another. Similarly for pair swapping and part swapping it is the pair group and part group values that determine that a differential pair or sub part can be swapped respectively.
The swap groups for a component are configured in the Configure Pin Swapping dialog, shown in the image below. It is accessible by right clicking on the component in the Schematic or PCB editors and selecting the Part Actions » Configure Pin Swapping or Component Actions » Configure Pin/Part Swapping menu items respectively. The Configure Pin Swapping dialog can also be accessed through the Configure Pin Swapping Information In Components dialog.
Setting up the pin swap groups in the Configure Pin Swapping dialog for a Dual 5-Input NOR Gate component.
Pin Groups
A component pin is swappable with another pin in that component when it belongs to the same pin group (has the same pin group value). The pin group is an attribute of each pin in the component and its value can be any alphanumeric string. The pin groups for the entire component are set up in the Configure Pin Swapping dialog, as shown in the image above.
Schematic containing a Dual 5-Input Positive-NOR Gate component. Each of the input pins for either sub parts are logically equivalent and presenting an ideal situation for pin swapping.
Considering the schematic shown in the image above, which contains the two 5-Input NOR Gates for the SNJ54S260 component, each of the nets INA0 to INA4 can be swapped with each other due to the nature of the NOR Gate. Similarly each of the nets INB0 to INB4 can be swapped, however a INAx net can not be swapped with a INBx net.
The swapping constraints for the NOR gate are defined in the Configure Pin Swapping dialog shown in Figure 2. Giving the nets INAx the swap group 1, and the nets INBx the swap group 2 ensures that swapping will only be preformed by the system in such a way that it is consistent with the component logic.
Leaving the Pin Group value for a pin empty means it is unavailable for swapping. In the case of Figure 2 it does not make sense to interchange the output and power pins (Designators 5,6,7 and 14) with each other and so the pin group is left blank.
Part Groups and Sequence IDs
It is common for a component to consist of multiple functionally equivalent subparts. Part swapping allows the nets of such equivalent sub-parts to be swapped. Consider again the component of shown in the image above. Both NOR gates offer identical functionality and the nets (INA0, INA1, INA2, INA3, INA4, OUTA) are able to be swapped with nets (INB0, INB1, INB2, INB3, INB4, OUTB).
Part swapping for a component is configured with the part group and sequence ID attributes. These are both text attributes and are accessible in the Part tab of the Configure Pin Swapping dialog, as shown below. displays the part group and sequence ID settings corresponding to the component shown in the image above. The part group indicates which sub-parts are able to be swapped with one another. The two sub-parts are able to be swapped and consequently, in the image below, their part groups are given the same value of 1.
The sequence ID attribute determines equivalence of the pins between swappable sub-parts. In the NOR gate example it is important that the input pins are not interchanged with the output pins when a part swap occurs. The image below shows the sequence ID are set so that OUTA swaps with OUTB, INA0 swaps with INB0, INA1 swaps with INB1 and so on.
Setting up part swap groups in the Configure Pin Swapping dialog for a Dual 5-Input NOR Gate component.
Note that Part Swapping is only available for components designed as sub-parts as it is based upon swapping all the nets between two sub-parts.
Pair Groups
The swapping of differential pairs is governed by the value of the pair group for a differential pair. The pair group attribute is accessed in the Differential Pair Swapping tab of the Configure Pin Swapping dialog. There are three modes in the Differential Pair Swapping tab that can be set by the drop down box in the lower left corner.
- Show Pairs From Directives - The system will use differential pair directives placed on the schematic to populate the differential pairs in the table.
- Show Pairs From FPGA - The system will use differential pair data obtained from FPGA information available to the component to pair up the pins. Note that this mode is available when the component is an FPGA.
- Show All Pins - The system will display all the component pins.
Setting up Pair Swap groups in the Configure Pin Swapping dialog.
Controlling How the Swaps are Performed on the Schematic
In the PCB editor pin, pair and part swaps are performed by exchanging nets on component pads and corresponding copper. When the changes are merged into the schematics there are two ways that a pin swap can be handled, either by swapping the pins on the component symbol, or by swapping net labels on the wires attached to the pins. Each approach has its advantages and disadvantages.
Swapping the pins will always work on the schematic, but it may mean that this instance of the component symbol is no longer the same as it was defined in the library. In this situation it means the symbol cannot be updated from the library, and it also means that other instances of the same component in this design will have a different pin arrangement, a possible source of confusion to someone reading the schematic. This approach is ideal for simple components, such as a resistor arrays.
Performing the swap on the schematic by swapping net labels can only be done if the connectivity is established through the net labels, that is, if the pins are not hard-wired together. The advantage of this approach is that the component symbol does not change, and can be updated from the library at a later date. This approach is the best choice for a complex component, such as an FPGA, where physically moving two pins on the symbol could result in an I/O bank-based symbol presenting incorrectly.
Selecting which of these two approaches is used is determined by the Allow Pin Swapping Using these Methods options in the Options for Project dialog, as shown below.
These project options govern how pin swaps are updated in the schematic documents.
Enabling Pin, Pair and Part Swapping on the PCB
The swap group attributes needed to setup pin, pair and part swapping within a component are stored in the Schematic components. However it is the PCB editor where this information is used and each PCB component has an option to allow pin swapping of its pins.
The swapping options for each PCB component can be configured in the Component Properties dialog (accessible by double clicking on the component or right clicking and selecting properties) under the Swapping options section. These options can also be found in the PCB Inspector panel.
Swap Manager Dialog
The Swap Manager lists all components used in the design (or library), with their current swap settings. The PCB editor Swap Manager dialog includes additional columns for enabling/disabling swapping on each component on the board. The Swap Manager dialog is found in the tools menu of the Schematic, Schematic Library and PCB editors under the Configure Pin Swapping command.
The Swap Manager dialog.
The Swap Manager includes a powerful right-click menu, making it very easy to quickly copy the settings from one component to another, or enable/disable multiple components in a single click.
Double clicking on a component in the Swap Manager will open the Configure Pin Swapping dialog for that component, where you can define the swap group settings for pins, differential pairs and subparts.
Performing Pin, Pair and Part Swaps
Interactive Pin, Pair and Part Swapping
Interactive swapping allow pins, differential pairs or subparts to be swapped one at a time in the PCB editor. The interactive swapping commands are found in the Tools » Pin/Part Swapping sub-menu. Once the command is selected from the menu the pins that are available for swapping are highlighted. The steps required to preform a swap are displayed on the Status line;
- The first step is to select one of the highlighted pins that will become the source of the pin swap. In the case of pair or part swapping the differential pair or sub-part that the pin belongs to will be subsequently swapped.
- The second step is to select the target pin for the swap. For pair or part swapping this pin will be representative of a differential pair or a sub-part.
Continuing with the example of Figure 4 the stages of interactively part swapping the Dual 5-input NOR gate component are shown in the two images below. There are two subparts that can be swapped and so each of their five pins can be selected, as shown in the image above. Pin 8 is selected corresponding to the subpart U2B. The system then highlights the pins of subpart U2A that can be swapped.
First image, step 1 - select a pin to be swapped, available pins will highlight. Second image, step 2 - select a target pin.
Automatic Pin/Net Optimizer
The Automatic Pin/Net Optimizer is a two-stage tool. Select Tools » Pin/Part Swapping » Automatic Pin/Net Optimizer from the PCB editor menu to perform an automatic optimization.
The Automatic Pin/Net Optimizer first runs a fast single-pass optimizer that attempts to minimize cross overs and connection lengths, but may actually increase them. When this is complete you will be asked if you want to run the iterative optimizer. The iterative optimizer will perform multiple passes in an attempt to reduce the number of cross overs and connection lengths.
Passing the Changes Back to the Schematic
When you configure the swap groups in the Configure Pin Swapping dialog the edits you make are immediately applied to the schematic components, regardless of which editor was active when the command was launched. However design changes that are a result of you performing a pin, differential pair or subpart swap in the PCB editor are propagated back to the schematic using the standard Design Update process.
Pushing the Changes from the PCB to the Schematic
Pin, pair and part swaps are passed back to the schematic in the same way that other design changes are transferred - by selecting Design » Update from the menus. Depending on how the Allow Pin Swapping options are configured, pin swaps will be performed as:
- Change Pin Names - this change will move the pins on the symbol. The pins are not actually moved on the symbol, internally the definition of the two pins are swapped over, however, visually it will appear that the two pins have moved, swapping locations.
- Move Pins to Different Nets - this change will swap the net labels on the attached wires
- Change Sub-Part ID - this change will simply change the sub-part index when a part swap is performed.
The first image shows a pin swap resolved in the schematic by swapping pins. The second image shows the swap resolved by moving the net labels.
If the schematic does not udpate to show swapped pins or parts, press the End key to refresh the display.
Taking Advantage of the New Pin/Part Swap System with FPGA Designs
Other than the obvious advantages that intelligent pin, pair and part swapping provides, the ability to swap partially routed sub-nets brings a new dimension to swapping, that is ideal for working with large capacity FPGAs. The dynamic net re-assignment allows you to use a multi-stage design process, with progressively refined pin/net assignments.
Initial I/O Assignment
In this stage the FPGA's and other device pins have their net assignments setup in whatever way is easiest at the schematic level. Usually this means just adding net labels in numeric bus order to the pins on the FPGA. The Smart Paste feature in the Schematic Editor is ideal for doing this.
Initial Connection Optimization
The design can be transferred to PCB layout, where there will be a lot of connection crossovers because of the random assignment at the schematic level. Running the Automatic Net/Pin Optimizer command will quickly provide a large reduction in the number of crossovers. The result does not need to be ideal yet, it is just to make things a more visually manageable at the PCB level.
Escape Routing
Fanout and Escape routing can now be performed on large devices on the PCB (right-click on the component to selectively perform fanout/escape routing). This may worsen the previously optimized assignments, but that does not matter at this point.
Escaped Connection Optimization
Run the automatic optimizer again, this time it will take advantage of the pre-routed sections of fanout/escape routing.
Manual Routing
You can now treat the ends of the escape routes as 'targets' to route towards. Ignoring the actual connection lines, you can route from the other ends of the nets toward the nearest escaped I/O route (spatially and by layer) on the PCB, rather than the one that is on the same net. The connections will not line up, instead you will end up with a series of small gaps between the escape routing from the FPGA I/O pins and your routing coming from other parts of the PCB. The image below shows a simple example of this.
Final optimization
Run the automatic optimizer again and it will assign the routed subnets to the closest possible escaped I/O pin. This will leave you with a set of very short connections to complete. The automatic optimizer has special routines to produce a good result in this case. These can now be interactively or automatically routed.
Manual Pin Swaps
Use the interactive swapper to perform any specific pin swap changes that you need.
Propagate Changes Back to Schematic
When you are ready to propagate these pin assignments back to the schematic, it is a good idea to disable pin changes on the schematic symbols. This is because FPGAs are often presented as multi-part components, with each bank of pins being a separate schematic part. Moving pins from one part to another would result in these symbols becoming logically incorrect, as the bank symbol would include pins that did not belong in that bank. In this situation performing pin swaps by changing net labels is the correct approach.
Repeat as Often as Required
This process can actually be run as many times as required, and at any time during the design process.