Altium NEXUS 版本发布说明
Created: 七月 21, 2019 | Updated: 七月 21, 2019
| Applies to version: 2.1
您正在阅读的是 2.1. 版本。关于最新版本，请前往 Altium NEXUS 版本发布说明 阅读 5 版本
The following sections list the release notes for publically released versions of Altium NEXUS 2.1
Version 2.1.6
Build: 59 Date: 17 July 2019
| 32101 | Fixed a bug that occurred when importing projects with the CADSTAR importing wizard. |
| 32221 | The origin in the PCB library editor is now snapped to correctly when Footprint Origin snapping is enabled. |
| 32224 | Fixed a bug that made it impossible to change settings for snapping. |
| 32228 | The midpoint of a pad edge is now snapped to if Pad Vertices is enabled as an Object for Snapping. |
| 32229 | The last-placed via stack configuration is now saved as preferred during the current PCB editing session and is then used for the next routing layer change (if applicable). |
| 32236 | Fixed a bug where gerber file extensions featured in Layer Stack Tables of PCB documents did not correspond to the correct file extension. |
| 32286 | The Grids, Guides & Axes snap enable buttons have been added to the Properties panel in the PCB library editor (BC:11187). |
| 32562 | Fixed an error that occurred when Altium NEXUS was starting if it was resized, minimized, and displayed an active Draftsman document. |
| 32595 | Fixed regression where the Fill Style applied to a Draftsman Circle object is not visible. |
| 32629 | Fixed issue where the target Differential Pair Tuning length match could not be achieved when xSignals are applied. |
| 32784 | Fixed issue where unconnected mid-layer pads are incorrectly included in the Gerber output when Backdrilling is applied and the 'Include unconnected mid-layer pads' option is unchecked (BC:11121). |
| 32925 | Fixed regression in 2D/3D PCB display rendering where the Plane Clearance was not visible for Backdrilled holes (BC:10808). |
| 32994 | Fixed an Ansys EDB Exporter bug that caused some pad sizes to increase in size when opened in Ansys software. |
| 33214 | Fixed an issue with the Draftsman Layer Stack Legend that caused Backdrill Vias to start from the Surface Finish Layer rather than the Top/Bottom Layer in symmetrical layer stacks. |
| 33218 | A new Surface Finish layer has replaced the Copper plating layer within the Layer Stack Manager. |
| 33245 | Fixed an issue with the Ansys EDB Exporter where origin errors would occur when a comma has been used as the decimal separator. |
Version 2.1.5
Build: 53 Date: 7 May 2019
Platform
| 30138 | The Date/Time format that is shown for projects listed in the Open Project dialog is now determined by the PC's system Region settings. |
| 30249 | Fixed crash that occurred when attempting to move and dock a panel onto a second, non-active design window in another monitor. |
| 30511 | Resolved a number of UI issues, including: dialogs not applying the selected UI Theme, dialog not retaining its on-screen location, PCB measurement text not scaling correctly, and poor quality images in the xSignals Wizard. |
| 30656 | Renamed Debug log now generated in the ...\AppData\Local\Altium\[Product GUID] folder rather than in the current project folder (BC:10462). |
| 30722 | Updated the way path preferences are stored and handled to avoid local environment path aliases (BC:9552). |
| 31089 | Fixed localization issue with Search hotkey. |
| 29016 | Support added for Eagle 9.x format along with numerous fixes and enhancements. |
| 30784 | Fixed bugs in a range of third-party design project importers including; Allegro, Eagle, OrCAD, PADS Logic, PADS Layout, xDX Designer, Xpedition, Zuken CR5000. |
| 31027 | Fixed bug in DXF/DWG export to now include user-defined relative reference origin in exported file (BC:8195). |
Data Management
| 23815 | Fixed a "Git repository not clean" error reported by the Project Releaser when a local project file is out of date with the VCS project files. |
| 25824 | The Custom Filter feature is now available from the column listing Filter options in the both a BOM document and the Components panel. |
| 28696 | Fixed bug where Project Releaser would hang when generating an ODB++ output file. |
| 29071 | Fixed bug where system GDI objects and memory would not be released if the Project Releaser is run and closed multiple times. |
| 29752 | Fixed bug where a selected Template was not applied when using the Component Editor in batch mode. Also added automatic sorting and the option to select no template. |
| 30104 | Improved Library Migrator performance. |
| 30224 | Fixed bug that reported a "Git repository not clean" error in response to a VCS conflict caused by a remote update to the active project. |
| 30398 | Fixed error "Can't perform revision status validation: Revision not found" on compile after PCB PCB and using Project Releaser (BC: 8273). |
| 30444 | Fixed an issue where the software would freeze for a period of time, with the message "Starting PCB Editor..." in the Status Bar, when clicking on *.DbLib in the Categories within the Components panel. |
| 30526 | Resolved issue where the error "Duplicated primary key" could occasionally occur when right-clicking in the Explorer panel. |
| 30603 | Fixed an issue that caused the software to freeze when switching between schematics of managed projects. |
| 31032 | Added horizontal scroll bar to Variant Manager dialog for better access to multiple variant entries (BC:9814). |
| 31247 | Added the option in the Library Migrator to migrate local datasheets. |
| 31644 | Resolved an issue where the incorrect time and author credentials were being stored during a GIT comment. |
| 31940 | Fixed regression that caused the custom resizing of the Components Panel to not be saved. |
| 31976 | Fixed a bug with 'Where Used' section in Replace Component dialog not allowing to follow Where Used links. |
Schematic
| 28002 | Fixed bug where the Properties panel would open in Component rather than object primitive mode when a SCH Library primitive is selected. |
| 29122 | Fixed bug that caused incorrect schematic Snap Grid behavior after the software has been restarted, and where the Windows region is set to German. |
| 30288 | Fixed "Can't perform revision status validation" error when updating PCB documents after annotation. |
| 30484 | Fixed bug that caused an updated component to adopt the default rather than the preferred footprint. |
| 30596 | Added automatic saving of Symbol Wizard window's position, size, and layout. |
| 30616 | Revised component identification logic and parameter handling to improve library generation (Make Library) process. |
| 30854 | Fixed Variants regression where the specified font color style for parameter variations is not shown in the schematic (BC:10440). |
| 30857 | Fixed bug that reset the user's font back to 'Times New Roman' during the 'component replacement' actions (BC:2727). |
| 31025 | Fixed an issue where part references (Right-click, References sub-menu) to documents in a local folder would show no results (BC:2989). |
| 31040 | The Port Cross Reference text for a Port symbol is now automatically placed on the opposite side of a Signal Harness entry (BC:10424). |
| 31260 | Fixed a regression issue where reopening a schematic document in which, as part of its previous editing session, the Edit » Move » Bring to Front command had been used, caused an error. |
| 31364 | Fixed software performance degradation when a significant number of database library components are placed in a design. |
| 31744 | Fixed an issue where a diff pair class could not be added to a group of selected directives. |
| 32014 | Fixed bug that caused a violation when adding Class Name to a diff pair that has been created on-the-fly. |
Part Search
| 29731 | Fixed bug in Manufacturer Part Search panel where the specified column order was lost when an additional page listing is loaded. |
| 29792 | Fixed bug where a configured Custom Parts Provider with an Excel source could not be accessed by the Manufacturer Part Search panel. |
| 30208 | Fixed bugs in the compact (narrow) mode of the Manufacturer Part Search panel where the Search results were not shown, the Details section lacked scrollbars and the first listed entry would be cropped after a panel resize. |
| 31183 | Resolved an issue where the Manufacturer Part Search Filter panel was incorrectly handling leading zeros in values, for example in the component Case category (BC:10874). |
| 31523 | Resolved an issue where pricing information would include redundant spaces around the = symbol if the Suffix option was enabled in the part provider Parameter Import Options. |
BOM
| 27304 | Fixed bug where BOM output report to template loses formatting when 'MS Excel File' format type is selected. |
| 28895 | Fixed an issue where the BOM Checks validation report, defined in an Output Job file, would never fail - as part of board release using the Project Releaser - when at least one fatal error exists. |
| 29347 | Resolved an issue where an MS Excel File (*.xls, *.xlsx) format BOM would sometimes cause an error while attempting to apply the selected Excel template. |
| 29373 | Added the ability to select and use file-based Library components ('unmanaged' components) when changing/replacing existing components from the ActiveBOM. |
| 30375 | Fixed bug that prevented the ActiveBOM line Start number being set to greater than 1000 in the Line |
| Options dialog. | |
| 30803 | Resolved an issue where the BomDoc settings, such as Solutions per Item, were not propagating through to the OutJob or the BOM Report. |
| 30986 | Fixed issue where hidden Excel sheets in the template were not recognized for BOM reports (BC:10638). |
| 31269 | Fixed bug where ReportDate field is incorrect in BOM generated from Template when System Region is set to Dutch. |
| 31682 | Fixed an issue where an exception was being thrown when attempting to generate a BOM report in Excel format ('Exception from HRESULT: 0x800AC472'). |
PCB
| 24898 | Fixed bug that prevented DRC violations (such as clearance issues) being detected in folded rigid-flex board designs (BC:9007). |
| 25738 | Additional PCB object snapping options implemented through the Board Properties panel (popup shortcut CTRL+E) (BC:7998; BC:5591). |
| 25883 | Fixed PCB primitive positional data rounding bug, as observed in the Properties panel when multiple aligned pads are selected. |
| 27818 | Fixed bug where, under certain conditions, Waived Violations would return as Violations after running a design rule check. |
| 28440 | Fixed bug where PCB Layer Stack Table could not be manually resized using its object handles. |
| 28447 | Fixed regression where Polygon or Region vertices data could not be pasted, or imported from a CSV file, into the Outline Vertices section in the Properties panel (BC:9873). |
| 29574 | Fixed regression where all Pads/Vias are shown in the 'Update Pads/Vias' dialog rather than just those that require updating. |
| 29889 | Fixed regression where the PCB editor Dim, Mask and Net highlighting modes would reset after the display has been cycled between 2D and 3D modes. |
| 30081 | Correct impedance profile is now loaded into the rule after importing stackup file. |
| 30350 | Fixed layer stack Material Library bug where all mandatory parameter fields were not shown for a new material entry if columns have been previously hidden. |
| 30528 | Fixed bug in IPC-2581 output generator that caused incorrect board outlines by rendering Arcs is the wrong rotational direction (BC:9884). |
| 30550 | Fixed bug that caused a crash when the system language is set to Korean and a Design Rule file (*.RUL) is imported. |
| 30706 | Fixed memory leak bug in router engine used for processes such as Move Component and Interactive Routing. |
| 30776 | Fixed issue where xSignals became to be broken after PCB Re-Annotation (BC:9862). |
| 30817 | Fixed bug where saving a corrupted STEP footprint model along with other footprints would cause all STEP models to be converted to extrusions. |
| 30913 | Added common default PCB snapping settings in Properties Panel and Active Bar (Shift+E to cycle snap options, CTRL+E to popup snapping options). |
| 30927 | Fixed regression that prevented the specified layer of an active Layer Set being restored after a different layer was made active. |
| 30934 | Quick access to snapping was added in Active bar. Snapping options now available during interactive processes (shortcut Ctrl+E) (BC:9759). |
| 30938 | Resolved an issue where changing the design rule scope and re-running the DRC could cause an access violation. |
| 30964 | fixed an issue where were no possibility to export/import mechanical layers and layer pairs in PCB Library. |
| 30982 | Fixed regression that caused a violation when placing an embedded board array. |
| 31012 | Restored PCB dimensioning features: Center, Baseline dimensions, and Linear and Radial Diameter dimensions (BC:8946, BC:9257, BC:8936). |
| 31026 | Fixed bug where mechanical layer primitives were included in a component bounding box definition (BC:1261). |
| 31033 | Added ability to manage the columns display in the Layer Stack Table - show/hide, edit names and modify the order (BC:7597). |
| 31036 | Added Gerber Name column availability to Layer Stack Table (BC:3623). |
| 31037 | Added calculated Total Board Thickness option to Layer Stack Table (BC:9225). |
| 31038 | Updated Layer Stack Table layer numbering to be synchronized with the copper layer numbering in the Layer Stack Manager (BC:10123). |
| 31039 | Resolved an issue where PCB cutouts were included in print outputs (BC:461). |
| 31133 | 3D Body placement split into two commands - use Place » 3D Body to place an MCAD model, or use Place » Extruded 3D Body to commence interactive placement of an extruded 3D Body object (same behavior as the AD19.0 Place » 3D Body command) (BC:10675; BC:9734). |
| 31135 | Updated 2D/3D functionality so that an object's 2D geometry is still visible when its 3D body Opacity is set to 0% (BC:1867). |
| 31141 | Fixed bug that caused a Gerber output to generate Mid Layer Pads in incorrect positions when the board source is a Mirrored Embedded Array. |
| 31168 | Fixed bug where the Plated Via information was missing from Gerber X2 outputs generated from an embedded board array (panelized source). |
| 31169 | Fixed bug where the Slice Track feature was not available in the PCB Library editor (BC:8943). |
| 31296 | Fixed an issue that caused Display Clearance Boundaries when routing to be blocked/overlapped by polygons. |
| 31323 | Added ability to set PCB Keepouts to Draft, Hide and variable Transparency (BC:10357; BC:10292). |
| 31339 | Added layer color crosshatch fills to PCB Keepouts (BC:4750). |
| 31356 | Added Properties support for the columns management in Layer Stack Table (BC:7597). |
| 31368 | Fixed regression where xSignal values are shown as 'BROKEN' for particular PCB design documents. |
| 31434 | Resolved an issue in the IPC-2581 output where nets connected by a net-tie were reported as different nets. |
| 31612 | Restored PCB Sheet Settings for Board options layout in the Properties panel (BC:8600). |
| 31622 | Resolved an issue where the copy/paste reference point was not defined correctly when pasting. |
| 31648 | Fixed an issue in PCB where zero-length tracks were added if the component was moved in some specific situations. |
| 31649 | Resolved an issue where DXF/DWG export would report "Failed to export", even though the DXF/DWG file was correctly generated. |
| 31675 | Resolved an issue where changing the relative origin would set it 1 grid unit left of the click location. |
| 31842 | Fixed an issue where the X, Y coordinate values from the PCB list panel were changed to incorrect values when using decimal "," symbol in Windows Regional settings. |
| 31893 | Fixed regression that caused all pads and vias to be displayed when invoking the Update Pad/Via Templates command even though they did not need to be updated. |
| 31942 | Fixed bug where the 'Keepout Region' was replaced by 'Copper Region' during the "Make PCB Library" process (BC:5538). |
| 32063 | Fixed issue that caused Xsignals to break after routing was completed by manually moving tracks or by interactive routing. |
| 32070 | Added option to "Merge Net-Tie Nets" for ODB++, IPC-D-356A and IPC-2581 output (BC:961, BC:3738). |
| 32102 | PCB Snapping Options have been updated with separate Grids, Axes and Guide options. Also snapping To Grids and Guides now works independently on Global enable\disable options (shortcut Ctrl+E). |
| 32122 | The Mechanical Layer number is now shown in the View Configuration Panel. |
| 32163 | Fixed bug where the HDI - TH vias were absent in NC Drill output if there were uVias with the same Start Top and Stop Bottom layers (BC:11078). |
| 32190 | Fixed an issue with Interactive length tuning 'From Rules' when changing Target length causes causing continuous DRC loop until an accordion is unselected. |
| 32208 | Fixed crash when opening a specific PCB document if the PCB List Panel is open. |
Draftsman
| 18437 | Added Draftsman X/Y axis scale object that can be placed and attached between any two drawing viewpoints. |
| 21531 | Added Draftsman Bookmarks TOC data to its PDF output generation process (BC:6614). |
| 25612 | Added ability to place dimensions to any primitive (BC:7287; BC:9574). |
| 30379 | Column Physical Layer Number was added to the Layer Stack Legend in Draftsman. |
| 30587 | Added Draftsman capability for a single Callout to apply to multiple sources/points on the document. |
| 30753 | Fixed bug that prevented the placement of Draftsman drawing views if components have a '/ ' character in their name and FIPS system cryptography algorithms are enabled (BC:10507). |
| 30838 | Fixed Draftsman regression that caused drill Symbols to be flipped (mirrored) in a placed Drill Drawing View. |
| 31382 | Fixed regression that caused a Draftsman document to not be allowed to be saved after importing changes from the PCB document. |
| 31514 | Fixed font rendering bug in Draftsman Assembly Drawing output caused by a recent Windows update "1809" (BC:10498). |
| 31634 | Added Diameter Dimension object to Draftsman. |
| 31683 | Fixed an issue where layers were missing a Fabrication View on certain Draftsman document designs, despite graphics still being present on the PCB. |
| 31714 | Fixed regression where snapping was displaced while editing objects in Draftsman. |
Multi-board
| 27474 | Fixed bug in Multi-board PCB display where Arcs on solder Mask layers were not being shown. |
| 28996 | View Configuration panel added to the Multi-board Assembly Editor. Use the panel to configure the Projection style, the Section View mode and planes, and the System Color assignments. |
| 29687 | Restored the ability to change PCB layer visibility in the Multi-board Assembly panel (BC: 10616). |
| 30163 | Section View now supports separate X, Y and Z section planes. Planes are are enabled and their orientation set in the View Configuration panel. Section View has 3 display modes, Off, On (sectioning applied, planes not visible), and Edit (sectioning applied, planes visible and editable). Drag a colored axis handle to move that section plane. |
| 30194 | Fixed 3D rendering issue in Multi-board Assembly view that can occur with PCB designs that include extruded 3D bodies. |
| 30199 | Fixed bug where blind vias were displaying as thru-hole vias. |
| 30496 | Added Multi-board option to skip free 3D bodies during ECO or when importing board file. |
| 30497 | Added Multi-board options to set components or STEP models to semi-transparent (BC:9454). |
| 30674 | Added OutJob support for exporting Multi-board Assembly as STEP or Parasolid X_T output. |
| 31071 | STEP models in a Multi-board assembly can be updated via the new right-click > Update Selected 3D Body command, the object's location and user-defined Mates are retained. |
| 31346 | Resolved an issue where the Multi-board schematic editor would display the From pin as the To pin in the Connections section of the Properties panel. |
| 31772 | Added keyboard shortcut L to open the Multi-board Assembly View configuration panel. |
Components Panel
| 28243 | Components panel - Favorites feature added to the Parameters listed in the Details section, now lists starred (Favorite) parameters when the list is in Show Less mode. Expand parameter list to access star feature, right-click to reset. |
| 29386 | Updated Components panel to not show PCB Library files when only a schematic type file is open for editing. |
| 29890 | Fixed bug in Components panel where a Favorite filter (starred) was not correctly retained between sessions or panel instances and did not appear at the top of the Filter listing. |
| 30441 | Fixed Components panel bug where its Categories navigation tree did not refresh after the Component Types list has been edited in Preferences. |
| 30608 | Added 'Find Similar Components' feature to the Components panel - accessed by right-clicking on a listed component. |
| 31072 | Fixed regression where the order of file-based libraries listed in the Components panel did not match that specified in the File-based Libraries Preferences (BC:10464). |
| 31201 | Improved Components panel Categories loading speed when a large number of unmanaged (file-based) libraries are installed. |
| 31288 | Added ability to select then edit or add to an active Search string 'breadcrumb' in the Components panel and the Manufacturer Part Search panel (BC:10787). |
| 31562 | Fixed an issue where the Components panel did not restore the previous session after re-logging in. |
| 31650 | Fixed an issue that ignored some symbols in the Name field when creating a new component type in the Data Management - Component Types Preferences page. |
| 31806 | Fixed regression issue with Components panel when using SvnDbLib. Refresh Library now works as expected after updating the SvnDbLib (BC:1195). |