SimView_Cmd-MoveWaveCursorMoveWaveCursor_AD

Created: июня 12, 2016 | Updated: апреля 11, 2017 | Applies to versions: 15.1, 16.0, 16.1, 17.0, 17.1, 18.0, 18.1, 19.0, 19.1, 20.0, 20.1, 20.2 and 21

Вы просматриваете версию 16.0. Для самой новой информации, перейдите на страницу SimView_Cmd-MoveWaveCursor((MoveWaveCursor))_AD для версии 22

Parent page: SimView Commands

The following pre-packaged resources, derived from this base command, are available:

Select Minimum Point on Active Waveform

Applied Parameters: Minimum

Summary

This command is used to quickly move the currently selected measurement cursor to the minimum point on its associated waveform.

Access

This command can be accessed from the SimData Editor by:

Choosing the Wave » Select Minimum Point command from the main menus.
Clicking the button on the SimView Cursor toolbar.

Use

First ensure that the measurement cursor that you wish to use (A or B) is selected. Select the required cursor by clicking on its tab.

After launching the command, the cursor will be moved to the minimum point of the waveform to which it is currently associated.

Select Maximum Point on Active Waveform

Applied Parameters: Maximum

Summary

This command is used to quickly move the currently selected measurement cursor to the maximum point on its associated waveform.

Access

This command can be accessed from the SimData Editor by:

Choosing the Wave » Select Maximum Point command from the main menus.
Clicking the button on the SimView Cursor toolbar.

Use

First ensure that the measurement cursor that you wish to use (A or B) is selected. Select the required cursor by clicking on its tab.

After launching the command, the cursor will be moved to the maximum point of the waveform to which it is currently associated.

Select Next Peak: Right

Applied Parameters: PeakRight

Summary

This command is used to quickly move the currently selected measurement cursor to the next peak to the right, on its associated waveform.

Access

This command can be accessed from the SimData Editor by:

Choosing the Wave » Select Next Peak: Right command from the main menus.
Clicking the button on the SimView Cursor toolbar.

Use

First ensure that the measurement cursor that you wish to use (A or B) is selected. Select the required cursor by clicking on its tab.

After launching the command, the cursor will be moved to the next peak (along to the right) of the waveform to which it is currently associated.

Select Next Peak: Left

Applied Parameters: PeakLeft

Summary

This command is used to quickly move the currently selected measurement cursor to the next peak to the left, on its associated waveform.

Access

This command can be accessed from the SimData Editor by:

Choosing the Wave » Select Next Peak: Left command from the main menus.
Clicking the button on the SimView Cursor toolbar.

Use

First ensure that the measurement cursor that you wish to use (A or B) is selected. Select the required cursor by clicking on its tab.

After launching the command, the cursor will be moved to the next peak (along to the left) of the waveform to which it is currently associated.

Select Next Trough: Right

Applied Parameters: TroughRight

Summary

This command is used to quickly move the currently selected measurement cursor to the next trough to the right, on its associated waveform.

Access

This command can be accessed from the SimData Editor by:

Choosing the Wave » Select Next Trough: Right command from the main menus.
Clicking the button on the SimView Cursor toolbar.

Use

First ensure that the measurement cursor that you wish to use (A or B) is selected. Select the required cursor by clicking on its tab.

After launching the command, the cursor will be moved to the next trough (along to the right) of the waveform to which it is currently associated.

Select Next Trough: Left

Applied Parameters: TroughLeft

Summary

This command is used to quickly move the currently selected measurement cursor to the next trough to the left, on its associated waveform.

Access

This command can be accessed from the SimData Editor by:

Choosing the Wave » Select Next Trough: Left command from the main menus.
Clicking the button on the SimView Cursor toolbar.

Use

First ensure that the measurement cursor that you wish to use (A or B) is selected. Select the required cursor by clicking on its tab.

After launching the command, the cursor will be moved to the next trough (along to the left) of the waveform to which it is currently associated.

Версия для печати

If you find an issue, select the text/image and pressCtrl + Enterto send us your feedback.

Примечание

Набор доступных функций зависит от вашего уровня доступа к продуктам Altium. Ознакомьтесь с функциями, включенными в различные уровни Подписки на ПО Altium, и функциональными возможностями приложений, предоставляемых платформой Altium 365.

Если вы не видите в своем ПО функцию, описанную здесь, свяжитесь с отделом продаж Altium, чтобы узнать больше.

SimView_Cmd-MoveWaveCursorMoveWaveCursor_AD

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Was this page helpful?