PCB_Dlg-ImpedanceFormulaEditorImpedance Formula Editor_AD

Вы просматриваете версию 15.1. Для самой новой информации, перейдите на страницу PCB_Dlg-ImpedanceFormulaEditor((Impedance Formula Editor))_AD для версии 18.1

The Impedance Formula Editor dialogThe Impedance Formula Editor dialog

Summary

This dialog allows you to view and (if required) modifythe formulae used to calculate Impedance and Trace Width when using impedance-controlled routing.

Access

The dialog is accessed from the PCB Editor by clicking the Impedance Calculation button in the Layer Stack Manager dialog. The latter is accessed by choosing Design » Layer Stack Manager from the main menus.

Options/Controls

Microstrip Tab

Click this tab to access formulae used when a route has a plane layer present on only one side of it (referred to as a microstrip).

  • Calculated Impedance - this region of the tab presents the current formula used in the calculation of the routing impedance. The formula can be modified as required, either directly in-situ or through use of the Query Helper, accessed by clicking the Helper button. The default formula is:

(60/SQRT(Er*(1-EXP(-1.55*(0.00002+TraceToPlaneDistance)/TraceToPlaneDistance))))*LN(5.98*TraceToPlaneDistance/(0.8*TraceWidth+TraceHeight))

  • Calculated Trace Width - this region of the tab presents the current formula used in the calculation of the routing trace width, which is used in the impedance formula. The formula can be modified as required, either directly in-situ, or through use of the Query Helper, accessed by clicking the Helper button. The default formula is:

((5.98*TraceToPlaneDistance)/EXP(CharacteristicImpedance/(60/SQRT(Er*(1-EXP(-1.55*(0.00002+TraceToPlaneDistance)/TraceToPlaneDistance)))))-TraceHeight)/0.8

The following pair of buttons are available for each formula region:

  • Helper - click to access the Query Helper dialog with the current formula loaded ready to make changes as required. While you can modify the formula directly in its region, especially if you are proficient with the Query Language, the Query Helper provides additional support with function keywords, operators and a syntax checker.
  • Default - click to load the region with the default formula.
Note that if the plane layer is not adjacent to the signal layer then the nearest plane layer will be used in the calculations.

Stripline Tab

Click this tab to access formulae used when a route has planes present on both sides of it (referred to as a stripline).

  • Calculated Impedance - this region of the tab presents the current formula used in the calculation of the routing impedance. The formula can be modified as required, either directly in-situ, or through use of the Query Helper, accessed by clicking the Helper button. The default formula is:

(80/SQRT(Er))*LN((1.9*(2*TraceToPlaneDistance+TraceHeight)/(0.8*TraceWidth+TraceHeight)))*(1-(TraceToPlaneDistance/(4*(PlaneToPlaneDistance-TraceHeight-TraceToPlaneDistance))))

  • Calculated Trace Width - this region of the tab presents the current formula used in the calculation of the routing trace width, which is used in the impedance formula. The formula can be modified as required, either directly in-situ, or through use of the Query Helper, accessed by clicking the Helper button. The default formula is:

((1.9*(2*TraceToPlaneDistance+TraceHeight))/(EXP((CharacteristicImpedance/(80/SQRT(Er)))/(1-(TraceToPlaneDistance/(4*(PlaneToPlaneDistance-TraceHeight-TraceToPlaneDistance))))))-TraceHeight)/0.8

The following pair of buttons are available for each formula region:

  • Helper - click to access the Query Helper dialog, with the current formula loaded, ready to make changes as required. While you can modify the formula directly in its region, especially if you are proficient with the Query Language, the Query Helper provides additional support with function keywords, operators and a syntax checker.
  • Default - click to load the region with the default formula.
Note that if the plane layers are not adjacent to the signal layer then the nearest plane layers will be used in the calculations. Note also that an offset stripline configuration is not supported.

 

If you find an issue, select the text/image and pressCtrl + Enterto send us your feedback.
Примечание

Набор доступных функций зависит от вашего уровня доступа к продуктам Altium. Ознакомьтесь с функциями, включенными в различные уровни Подписки на ПО Altium, и функциональными возможностями приложений, предоставляемых платформой Altium 365.

Если вы не видите в своем ПО функцию, описанную здесь, свяжитесь с отделом продаж Altium, чтобы узнать больше.