PCB_Cmd-SetCameraSetCamera_AD

Created: 8月 31, 2022 | Updated: 9月 15, 2022 | Applies to version: 22

This document is no longer available beyond version 22. Information can now be found using the following links:

Rotation Panning 3D View Controls

Parent page: PCB Commands

The following pre-packaged resources, derived from this base command, are available:

Rotate Left

Applied Parameters:To=30DegreeLeft

Summary

This command is used to rotate the board 30 degrees to the left.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

Choosing the View » 3D View Control » Rotate Left command from the main menus.
Using the Num4 keyboard shortcut.

Use

After launching the command, the board will rotate 30 degrees to the left. Multiple rotations may be performed.

The rotation angle step is set to 30° by default, and the pan distance step is set to 500mils (12.7mm) by default. These settings can be accessed and edited in the Other section of the PCB Editor - General page of the Preferences dialog.

Rotate Right

Applied Parameters: To=30DegreeRight

Summary

This command is used to rotate the board 30 degrees to the right.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

Choosing the View » 3D View Control » Rotate Right command from the main menus.
Using the Num6 keyboard shortcut.

Use

After launching the command, the board will rotate 30 degrees to the right. Multiple rotations may be performed.

Rotate Up

Applied Parameters: To=30DegreeUp

Summary

This command is used to rotate the board 30 degrees upward.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

Choosing the View » 3D View Control » Rotate Up command from the main menus.
Using the Num8 keyboard shortcut.

Use

After launching the command, the board will rotate 30 degrees upward. Multiple rotations may be performed.

Rotate Down

Applied Parameters: To=30DegreeDown

Summary

This command is used to rotate the board 30 degrees downward.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

Choosing the View » 3D View Control » Rotate Left command from the main menus.
Using the Num2 keyboard shortcut.

Use

After launching the command, the board will rotate 30 degrees downward. Multiple rotations may be performed.

Move Left

Applied Parameters: To=5000MilLeft

Summary

This command is used to move the board 500 millimeters to the left.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

Choosing the View » 3D View Control » Move Left command from the main menus.
Using the Ctrl+Num4 keyboard shortcut.

Use

After launching the command, the board will move 500 millimeters to the left. Multiple rotations may be performed.

Move Right

Applied Parameters: To=5000MilRight

Summary

This command is used to move the board 500 millimeters to the right.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

Choosing the View » 3D View Control » Move Right command from the main menus.
Using the Ctrl+Num6 keyboard shortcut.

Use

After launching the command, the board will move 500 millimeters to the right. Multiple rotations may be performed.

Move Up

Applied Parameters: To=5000MilUp

Summary

This command is used to move the board 500 millimeters upward.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

Choosing the View » 3D View Control » Move Up command from the main menus.
Using the Ctrl+Num8 keyboard shortcut.

Use

After launching the command, the board will move 500 millimeters upward. Multiple rotations may be performed.

Move Down

Applied Parameters: To=5000MilDown

Summary

This command is used to move the board 500 millimeters downward.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

Choosing the View » 3D View Control » Move Down command from the main menus.
Using the Ctrl+Num2 keyboard shortcut.

Use

After launching the command, the board will move 500 millimeters downward. Multiple rotations may be performed.

Rotate Left

Applied Parameters: To=RotateFit_Left

Summary

This command is used to rotate the board left.

Access

This command is accessed from the PCB 3D editor by:

Choosing the View » 3D View Control » Rotate Left command from the main menus.
Using the Num4 keyboard shortcut.

Use

After launching the command, the board will rotate left. Multiple rotations may be performed.

Rotate Right

Applied Parameters: To=RotateFit_Right

Summary

This command is used to rotate the board right.

Access

This command is accessed from the PCB 3D editor by:

Choosing the View » 3D View Control » Rotate Right command from the main menus.
Using the Num6 keyboard shortcut.

Use

After launching the command, the board will rotate right. Multiple rotations may be performed.

Rotate Up

Applied Parameters: To=RotateFit_Up

Summary

This command is used to rotate the board up.

Access

This command is accessed from the PCB 3D editor by:

Choosing the View » 3D View Control » Rotate Up command from the main menus.
Using the Num8 keyboard shortcut.

Use

After launching the command, the board will rotate up. Multiple rotations may be performed.

Rotate Down

Applied Parameters: To=RotateFit_Down

Summary

This command is used to rotate the board down.

Access

This command is accessed from the PCB 3D editor by:

Choosing the View » 3D View Control » Rotate Downcommand from the main menus.
Using the Num2 keyboard shortcut.

Use

After launching the command, the board will rotate down. Multiple rotations may be performed.

Roll Left

Applied Parameters: To=RollFit_Left

Summary

This command is used to roll the board left.

Access

This command is accessed from the PCB 3D editor by:

Choosing the View » 3D View Control » Roll Left command from the main menus.
Using the Num7 keyboard shortcut.

Use

After launching the command, the board will roll left. Multiple rolls may be performed.

Roll Right

Applied Parameters: To=RollFit_Right

Summary

This command is used to roll the board right.

Access

This command is accessed from the PCB 3D editor by:

Choosing the View » 3D View Control » Roll Right command from the main menus.
Using the Num9 keyboard shortcut.

Use

After launching the command, the board will roll right. Multiple rolls may be performed.

印刷用ページ

If you find an issue, select the text/image and pressCtrl + Enterto send us your feedback.

注記

利用できる機能は、Altium 製品のアクセスレベルによって異なります。Altium Designer ソフトウェアサブスクリプションの様々なレベルに含まれる機能と、Altium 365 プラットフォームで提供されるアプリケーションを通じて提供される機能を比較してください。

ソフトウェアの機能が見つからない場合は、Altium の営業担当者に連絡して詳細を確認してください。

PCB_Cmd-SetCameraSetCamera_AD

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Summary

Access

Use

Was this page helpful?