Pin

Now reading version 22.0. For the latest, read: Pin for version 21
 

Parent page: Schematic Objects

 The schematic Pin represents the physical component pin in the schematic design space. The schematic Pin represents the physical component pin in the schematic design space.

Summary

A pin is an electrical design primitive. Pins give a component (part) its electrical properties and define the connection points on the part for the incoming and outgoing signals.

Availability

Pins can only be placed in the Schematic Library Editor using one of the following methods:

  • Click Place » Pin from the main menus.
  • Click  on the drop-down of the Utilities toolbar ().
  • Right-click then choose Place » Pin from the context menu.

Placement

After launching the command, the cursor will change to a cross-hair and you will enter pin placement mode. Placement is made by performing the following sequence of actions:

  1. Click or press Enter to anchor the pin. Note that the floating pin is held by the electrical end, which must be positioned away from the component body. Only one end of the pin is electrical; it is always this end that the pin is held.
  2. Continue placing additional pins or right-click or press Esc to exit placement mode.

Additional actions that can be performed during placement – while the pin is still floating on the cursor, and before the electrical end of the pin is anchored – are:

  • Press the Tab key to pause the placement and access the Pin mode of the Properties panel from where its properties can be changed on the fly. Click the design space pause button overlay ( ) to resume placement.
  • Press the Alt key to constrain the direction of movement to the horizontal or vertical axis depending on the initial direction of movement.
  • Press the Spacebar to rotate the pin counterclockwise or Shift+Spacebar for clockwise rotation. Rotation is in increments of 90°.
  • Press the X or Y keys to mirror the pin along the X-axis or Y-axis.
While attributes can be modified during placement (Tab to access the Properties panel), keep in mind that these will become the default settings for further placement unless the Permanent option on the Schematic – Defaults page of the Preferences dialog is enabled. When this option is enabled, changes made will affect only the object being placed and subsequent objects placed during the same placement session.

Create the Library component near the origin (center) of the Library Editor sheet, which is marked by dark cross-hair lines. Typically a pin or the corner of the component body is placed at the sheet origin.

The pin number (Designator) must be defined since that is what is used to establish the connectivity. The Electrical Type is also important as this is used in the Schematic Editor for the Electrical Rules Check (ERC).

Adding Pins in the Component Pin Editor

Pins can also be added through the Component Pin Editor dialog, which is accessed by clicking the Pins button of the Properties panel in Component mode.

Add one or more pins in the Component Pin Editor dialog.

Click the Add button to add a new pin, then define the properties in the dialog. Note that multiple pins can be added and defined. You can also use Tab and Shift+Tab to step between the fields. 

Notes on Pin Numbering

For many components, there will be a series of pins that have numerical names and numbers. The Auto-Increment During Placement feature on the Schematic - General page of the Preferences dialog can be used to speed the placement of these pins. Auto-increment is invoked automatically if the pin properties are edited before placement (press Tab while the pin is floating on the cursor). The feature works for both the Designator and the Display Name - the pin Designator uses the Primary auto-increment field and the pin Display Name uses the Secondary auto-increment field. It supports ascending alpha and numeric values, and descending numeric values.

Configure the Auto-Increment During Placement settings on the Schematic - General page of the Preferences dialog.Configure the Auto-Increment During Placement settings on the Schematic - General page of the Preferences dialog.

 

Note the increasing alpha pin name and decreasing numeric pin number.

Graphical Editing

To move a pin, click and hold. The cursor will jump to the electrical hotspot end of the pin; move it to the new location, placing it with the electrical end away from the component body.

While dragging, the pin can be rotated (Spacebar/Shift+Spacebar) or mirrored (X or Y keys to mirror along the X-axis or Y-axis).

If attempting to graphically modify an object that has its Locked property enabled, a dialog will appear asking for confirmation to proceed with the edit. If the Protect Locked Objects option is enabled on the Schematic – Graphical Editing page of the Preferences dialog, and the Locked option for that design object is enabled as well, then that object cannot be selected or graphically edited. Click the locked object to select it then disable the Locked property in the List panel or disable the Protect Locked Objects option to graphically edit the object.

Non-Graphical Editing

Editing via the Pin Dialog or Properties Panel

Properties page: Pin Properties

The properties of a Pin can be edited in the Pin dialog and the Properties panel, which allows editing of all item(s) currently selected in the design space.

The Pin dialog, on the left, and the Pin mode of the Properties panel on the right The Pin dialog, on the left, and the Pin mode of the Properties panel on the right

After placement, the Pin dialog can be accessed by:

  • Double-clicking on the placed pin object.
  • Placing the cursor over the pin object, right-clicking then choosing Properties from the context menu.

During placement, the Pin mode of the Properties panel can be accessed by pressing the Tab key. Once the pin is placed, all options appear.

After placement, the Pin mode of the Properties panel can be accessed in one of the following ways:

  • If the Properties panel is already active, by selecting the pin object.
  • After selecting the pin object, select the Properties panel from the Panels button in the bottom right section of the design space or select View » Panels » Properties from the main menu.
If the Double Click Runs Interactive Properties option is disabled (default) on the Schematic - Graphical Editing page of the Preferences dialog, when the primitive is double-clicked or you right-click on a selected primitive then choose Properties, the dialog will open. When the Double Click Runs Interactive Properties option is enabled, the Properties panel will open. 
While the options are the same in the dialog and the panel, the order and placement of the options may differ slightly.

Pin Display Name and Designator - Position and Font

The location of the pin Display Name and pin Designator (number) is defined globally by the Pin Margin settings on the Schematic - General page of the Preferences dialog. This is an environment setting, meaning it applies to the PC where the setting is defined. The settings define a relative distance the text is away from the non-electrical end of the pin.

 Set the distance of the pin text (Pin Margin) in the Preferences dialog. Set the distance of the pin text (Pin Margin) in the Preferences dialog.

The default system font for a schematic library document is Times New Roman, 10pt, Regular. This is fixed and cannot be changed. When a library component is placed on a schematic sheet, this same default font is applied but is not fixed and can be changed as required. Keep in mind that the system font used for a schematic sheet applies to other objects as well, including Power Ports, Ports, and the X, Y region markers in the schematic sheet border.

For pins, these system-level settings of position and font can be overridden. Controls for customization of the position and font for a pin's Designator and Name can be found in the Pin mode of the Properties panel.

 The font and location of the pin Designator (number) and Name can be modified for individual pins if required. The font and location of the pin Designator (number) and Name can be modified for individual pins if required.

Use the Custom Position option to change the default settings for the position to an overriding, customized position. For the Margin, enter a new value directly in the associated field. For the Orientation, use the drop-down to choose the angle (0° or 90°) and the To reference (Pin or Component).

Use the Custom Settings option to change from following the default system font to an overriding, customized font. 

Pin Symbol Line Width

When representing a component in the schematic editing domain, each pin defined as part of that device's schematic symbol can have one or more symbols displayed. These are symbols displayed on the Inside, Inside Edge, Outside, or Outside Edge in relation to the main component symbol outline, as required. Examples might include a Clock symbol on the Inside Edge or a Dot symbol on the Outside Edge. Such symbols greatly improve the readability of the design through visual indication of the purpose of the signal traversing a particular pin.

Use the Line Width setting in the Symbols region of the Properties panel to specify the width of the line used to draw these symbols. Choose from either Small or Smallest.

Editing Multiple Objects

The Properties panel supports multiple object editing, where the property settings that are identical in all currently selected objects may be modified. When multiples of the same object type are selected manually, via the Find Similar Objects dialog or through a SCHLIB Filter or SCHLIB List panel, a Properties panel field entry that is not shown as an asterisk (*) can be edited for all selected objects.

Editing via a List Panel

Panel pages: SCHLIB List, SCHLIB Filter

List panel allows you to display design objects from one or more documents in tabular format, enabling quick inspection and modification of object attributes. Used in conjunction with appropriate filtering - by using the applicable Filter panel or the Find Similar Objects dialog - it enables the display of just those objects falling under the scope of the active filter – allowing you to target and edit multiple design objects with greater accuracy and efficiency.

Older designs sometimes included components with hidden power pins, which were connected to the appropriate power net. While this practice is not recommended, hidden pins can be connected by entering the net name in the Hidden Net Name field in the SCHLIB List or SCH List panels.

If you find an issue, select the text/image and pressCtrl + Enterto send us your feedback.
Note

The features available depend on your Altium product access level. Compare features included in the various levels of Altium Designer Software Subscription and functionality delivered through applications provided by the Altium 365 platform.

If you don’t see a discussed feature in your software, contact Altium Sales to find out more.

Content