操作SPICE网络列表

The SPICE netlist is a textual representation of the circuit. It must include all necessary components with parameters, component models, connections, and types of analysis. It is the SPICE netlist that is processed by the simulation engine. The graphical representation of the schematic is used to simplify the creation of the netlist from the user's work when simulating. Because the netlist is created automatically when designing the schematic, there is no need to create it manually, and that simplifies the process and reduces potential errors.

The specification of components and connections requires a special syntax to describe the circuit. Despite the complexity of the method, it has its advantages – it allows you to work directly with and simulate from a netlist, as well as from a schematic.

Components in imported designs or those placed from installed database libraries are included in the generated simulation netlist if they have an assigned simulation model.

Creating a Netlist

To generate the simulation netlist from your current schematic, select Simulate » Generate Netlist from the menus. To create a new, empty netlist, select the File » New » Mixed-Signal Simulation » AdvancedSim Netlist command from the menus.

To understand the content, consider an example netlist shown below that matches the schematic shown beneath it.

Example netlist.
Example netlist.

The schematic that the netlist was generated from.
The schematic that the netlist was generated from.

  • Lines with an asterisk * at the beginning are comments, used as an auxiliary text
  • CC11 0 NetC11_2 100nF is the component description, where:
    • CC11 component designation
    • 0 NetC11_2 – nets that the component's pins are connected to; in this example, the first pin of the capacitor is connected to the GND (0) circuit, the second to NetC11_2
    • 100nF – component value
  • VV6 NetC14_2 0 DC 0 PULSE(0 5 100n 10n 10n 400n 1u) AC 1mV 0 – signal source description:
    • VV6 – component designation
    • NetC14_2 0 – component connection pins
    • DC 0 / AC 1mV / 0 – signal source parameters: DC, AC, phase
    • PULSE(0 5 100n 10n 10n 400n 1u) – output signal parameters: Initial Value, Pulsed Value, Time Delay, Rise Time, Fall Time, Pulse Width, Period
  • .PRINT =1 NetC13_1 NetC14_2 – command to show signals in the form of a plot
  • *Selected Circuit Analyses:
    • .TRAN 1 10u 0 1 – selected type of calculation (transient calculation) and calculation parameters (start time, end time, step)
  • *Models and Subcircuits:
    • .model PMOSFET_Level1 pmos (Level=1) – link to the transistor model used
  • .END – end of the document

 

To run a simulation directly from an open netlist, select the Simulate » Run command from the main menus (shortcut: F9).

Areas of SPICE User Code

Areas of user SPICE-code is a mechanism for transferring Mixed Sim simulator commands from the circuit to the netlist. This mechanism is used to quickly prototype sections of the circuit, which enables whole SPICE code sections to be defined directly on the circuit, such as model definitions, parameters, and simulator instructions for calculations.

Areas of user SPICE-code cannot replace SPICE components completely. This means that it is not possible to generate a task for an electrical circuit simulator using only the SPICE user code areas. Therefore, this mechanism is a helpful addition for advanced users, but it does not exclude the need to describe the circuit in the schematic’s graphical format.

To define the area of user SPICE code:

  1. Add a Text Frame object on the schematic.
  2. Add the .nsx text as the first line in the text frame.
  3. Below the .nsx line, write SPICE code according to SPICE syntax requirements.

When generating a netlist, an area will appear containing text from the custom SPICE code section.

Within a schematic sheet, you can define as many areas of the user SPICE code as needed. All areas will be combined into a single block in the netlist.

An example of defining the areas of user SPICE code.
An example of defining the areas of user SPICE code.

Areas of user SPICE-code can be used to redefine the global parameters specified in the Global Parameters tab of the Advanced Parameters Settings dialog. When defining a parameter with the same name in the Global Parameters tab and in the user SPICE-code area, the Text Frame information will have the higher priority.
If you find an issue, select the text/image and pressCtrl + Enterto send us your feedback.

软件的功能取决于您购买的Altium产品级别。您可以比较Altium Designer软件订阅的各个级别中包含的功能,以及通过Altium 365平台提供的应用程序所能实现的功能。

如果您在软件中找不到某个讨论过的功能,请联系Altium销售团队以获取更多信息。

Content