交互式布线

Parent page: Routing the PCB

Routing is the process of defining a connective path between the nodes in each net. This path is defined by placing PCB design objects, such as tracks, arcs, and vias, on the copper layers to create a continuous connection between the nodes. Rather than placing these objects one by one to build up the connective path, you interactively route the connection.

In the PCB editor, interactive routing is an intelligent process. After launching the command, click on a pad to select a connection to be routed. The interactive router then attempts to define a route path from that pad, all the way to the current cursor location.

The size of the track that is placed is controlled by the applicable Routing Width design rule, and the clearance from other net objects is controlled by the applicable electrical Clearance design rule. How the interactive router responds to existing objects, such as pads and routing on other nets, depends on the current Routing Conflict Resolution mode. The mode determines whether the router will Walkaround the obstacle, or attempt to Push it, or Stop, or Ignore it.

Cursor guided routing makes complex manual routing around obstacles fast, easy and intuitive. In other words, you create the path of the route with your mouse and the Interactive Router attempts to place the tracks according to that path. This works in accordance with design rules and also with various constraints for track placement and corner types.

Interactive routing can be performed on:

• A single net - Route » Interactive Routing
• Two nets configured as a differential pair - Route » Interactive Differential Pair Routing
• A set of selected nets - Route » Interactive Multi-Routing

This article describes the process of interactively routing a single net, and the settings that control that process. If you are looking for information on specialized routing techniques, such as differential pair or controlled impedance routing, refer to the links on The Routing page.

Interactively routing a connection - after launching the command and clicking on a connection line, the Interactive Router finds a path from the net object to the current cursor location, weaving around existing objects.
A click of the mouse button will place all hatched track segments, Ctrl+Click to auto-complete the route.

Monitoring Connectivity during Interactive Routing

The PCB editor includes a net analyzer that constantly monitors the location of all objects in the design space and updates the connection lines when any net-type object is edited. The net analyzer monitors all the objects attached to a net, for example, when a connection is routed, the connection line between those two pads is automatically removed by the net analyzer. Or if a net is partially routed, then a shorter connection line will be displayed between the two closest route points on the net.

It does not matter if you choose to ignore the connection line and route the net from/to a different location. As soon as routing is terminated, the net analyzer runs and removes the connection line if it is no longer required, as shown in the video below.

Even though the connection line connects the pad centers, you are free to route wherever you choose. The net analyzer constantly monitors the routing progress and updates the connection line.

Because the arrangement of connection lines is determined by the routing topology design rule, it is possible that the connection line will not attach to the end of the track and instead attach to some other point in the net that is closer to another point in the net. If preferred, connection lines can be forced to the track ends by enabling the Smart Track Ends option on the PCB Editing – General page of the Preferences dialog. The video below demonstrates this. Note that you can force the net analyzer to run and update the connection lines by performing an action that the software sees as you editing an object belonging to that net. Edit actions include: moving an object, clicking and holding on an object, or double-clicking to display that object's properties in the Properties panel.

Note how the GND net connection line is attached to pad 1 instead of the end of the route. Once Smart Track Ends has been enabled and an edit performed, the connection line jumps to the end of the route.

How the Routing is Located in the Design Space

The PCB editor is a grid-based editing environment, the default behavior is for your interactive routing to be placed on the current snap grid. As well as the snap grid, the software includes a number of additional snap features, designed to help you accurately position and align design objects. Together, these features are referred to as the Unified Cursor-Snap System.

The key elements of this system include:

• User-Definable Grids - available in both Cartesian and Polar formats.
• Object Snapping - enabling placed objects to pull the cursor into position, based on cursor proximity to that object's snap points (hotspots). Use this to pull the cursor to the center of an off-grid pad, for example.
• Snap Guides - that can be freely placed and provide a handy visual cue for object alignment.
• Axis Snapping - a feature to pull the cursor, in either the X or Y direction, so that it axially-aligns with a near-by object's hotspot.

Demonstration of the cursor-snap features.

► Learn more about the PCB Grids System

The Basics of Interactive Routing

When you launch the interactive routing command and click on a connection line, the interactive routing engine will add a chain of connected track segments from the nearest existing net object, such as a pad or existing track, along the shortest available path to the current cursor location. 

Those track segments will be hatched, to show that they are proposed segments that have not yet been placed (uncommitted). When you left-click to place those segments they will become solid. These solid segments are actually referred to as soft commits - meaning the software recognizes them as segments you wish to retain, but the interactive routing engine may remove them or convert them back to uncommitted (hatched) if your routing path makes them redundant or creates an illegal shape. This behavior is demonstrated in the first video on this page.

Interactively routing a simple board.

Configuring the Interactive Router

The default settings for interactive routing are configured in the PCB Editor - Interactive Routing page of the Preferences dialog, as shown below (click  to open). Many of the settings can also be changed during interactive routing, in the Interactive Routing mode of the Properties panel. Press Tab during routing to display the panel.

  Configure the default interactive router settings in the Preferences dialog, then use the Properties panel to change settings as you route.

The following collapsible sections contain information about the Interactive Routing options and controls available:

Net Information

• Net Name – displays the name of the net to which the interactive routing is connected.
• Net Class – displays the net class that the interactive routing belongs to (if it is a member of a net class).
• Length – the total Signal Length. The Signal Length is the accurate calculation of the total node-to-node distance. Placed objects are analyzed to resolve stacked or overlapping objects and wandering paths within pads; and via lengths are included.
• Delay – the total delay of the selected segments, including those unrouted.

Select the clickable links of the Net Name, Net Class, Length, and Delay from the Interactive Routing mode of the Properties panel to be redirected to the PCB – Nets panel, where you may view and change details of the nets associated.

Properties

• Layer – use the drop-down to specify on which layer the routing is located.
• Via – if the via is associated with a template, the template name is displayed here.
• Via Diameter – specify the via diameter.
• Via Hole Size – specify the via hole size.
• Width – use the drop-down to specify the width.
  • Min – signifies that the design rule minimum width defined for the current net will be used
  • Preferred – signifies that the design rule preferred width defined for the current net will be used.
  • Max – signifies that the design rule maximum width defined for the current net will be used.

Interactive Routing Options

• Routing Mode – use the drop-down or use the Shift+R shortcut to cycle through the desired routing modes. The following choices are available:
  • Ignore Obstacles – select to ignore existing objects (routing can be freely placed). Violations are highlighted.
  • Walkaround Obstacles – select to have the Interactive Router route around existing tracks, pads, and vias. If this mode cannot walk around an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • Push Obstacles – select to have the Interactive Router move existing tracks out of the way. This mode can also push vias to make way for the new routing. If this mode cannot push an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • HugNPush Obstacles – select to have the Interactive Router hug existing tracks, pads, and vias as closely as possible and where necessary, push obstacles to continue the route. If this mode cannot hug or push an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • Stop At First Obstacle – in this mode, the routing engine will stop at the first obstacle that gets in the way.
  • AutoRoute Current Layer – select to enable auto-routing only on the current layer.
  • AutoRoute MultiLayer – select to enable auto-routing on multiple layers.
• Corner Style – select the desired routing corner style or use the Shift+Spacebar shortcut to cycle through the corner styles.
• Gloss Effort (Routed) – select the desired gloss level directly from the panel or use the Shift+Ctrl+G shortcut to cycle through the following choices:
  • Off – in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after routing/dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required (for example, when manually dragging tracks, cleaning pad entries, etc.).
  • Weak – in this mode, a low level of glossing is applied with the Interactive Router considering only those tracks directly connected to or in the area of the tracks that you are currently routing (or tracks/vias being dragged). This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical traces.
  • Strong – in this mode, a high level of glossing is applied with the Interactive Router looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly.
• Gloss Effort (Neighbor) – select the desired gloss level to apply to traces being pushed by the net currently being routed directly from the panel through the following choices:
  • Off – in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after routing/dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required (for example, when manually dragging tracks, cleaning pad entries, etc.).
  • Weak – in this mode, a low level of glossing is applied with the Interactive Router considering only those tracks directly connected to or in the area of the tracks that you are currently routing (or tracks/vias being dragged). This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical traces.
  • Strong – in this mode, a high level of glossing is applied with the Interactive Router looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly.
• Automatically Terminate Routing – when enabled, when you complete a route to the target pad, the routing tool does not continue in routing mode from the target pad but rather resets and is ready for you to click on the next source pad from which to route. If this option is disabled, after you route to the target pad, the tool will remain in routing mode and use the previous target pad as the source for the next route.
• Automatically Remove Loops – enable to automatically remove any redundant loops that are created during manual routing. This allows you to re-route a connection without having to manually remove redundant tracks. However, there are times when you need to route nets such as power nets and you need loops. You can toggle this option for a selected net by using the Shift+D shortcut to override this global setting for the same net.
• Remove Loops With Vias – enable to automatically remove loops with vias. Disable this option for vias to remain during loop removal.
• Remove Net Antennas – enable this option to remove any track or arc end that is not connected to any other primitive and forms an antenna.
• Allow Via Pushing – check this option to allow pushing a Via when in Push Obstacles or HugNPush Obstacles mode.
• Pin Swapping – check this option to enable pin swapping or use the Shift+C shortcut.
• Display Clearance Boundaries – enable to have the no-go clearance area defined by the existing objects and the applicable clearance rule displayed as shaded polygons within a local viewing circle or use the Ctrl+W shortcut to toggle on or off during routing. This option is not available in the Ignore Obstacles routing mode.
  • Reduce Clearance Display Area – enable to use a smaller clearance boundary. This option is available only when the Display Clearance Boundaries option is enabled.
• Show Length Gauge – enable to display the length gauge, which shows the current routed length. The gauge settings are calculated from the set of constraints defined by the applicable design rules. Use the Shift+G shortcut to toggle the display on or off during routing.
• Pad Entry Stability – protects centered pad entries. Use the slider bar to configure the level of protection:
  • Off = no protection
  • Max = maximum protection
• Miter Ratio – controls the minimum corner tightness. The Miter Ratio multiplied by the current track width equals the separation between walls of the tightest U-shape that can be routed for that ratio. Enter a positive value equal to or greater than zero (the x multiplier is added automatically).
• Subnet Jumper Length – specify the desired Subnet Jumper length.

Jumpers, which are also referred to as wire links, allow the designer to replace routing with a Jumper component. To learn more, see Working with Jumper Components.

Rules

Constraints defined by the applicable design rules will be listed under the Rules section of the Properties panel.

• Via Constraint – click to open the Edit PCB Rule dialog in which you can define PCB rules for a via.
• Width Constraint – click to open the Edit PCB Rule dialog in which you can define PCB rules for routing width.

Controlling the Corner Style

During interactive routing, the shape formed by the tracks and arcs that create a corner is referred to as the corner style. Diagonal corners are the most common, but curved corners (created by placing arcs), are also popular. There are 5 available corner styles, 4 of which also have corner direction sub-modes.

• Press Shift+Spacebar during routing to cycle through the corner styles, the current style is displayed on the Status bar ( ) and in the Heads Up display.
• Press the Spacebar to toggle the corner direction.
• Alternatively, press Tab to open the Interactive Routing mode of the Properties panel and change the corner style there.
• Press the 1 shortcut key to toggle between placing 1 segment per click (the first 5 images just below), or 2 segments per click (the last image in the set just below). In the first mode the hollow track segment is referred to as the look-ahead segment.
• Press the Backspace key to remove the last vertex.

Corner Style	Initial Corner Direction	Alternate Corner Direction	Notes
Track 45
Line 45/90 With Arc			Use the  &  keys to interactively change the arc radius, hold Shift to accelerate the radius change.
Track 90
Line 90/90 Vertical Start With Arc			Use the  &  keys to interactively change the arc radius, hold Shift to accelerate the radius change.
Any Angle			Use this mode in conjunction with Strong Glossing to perform snake routing.

Miter or Curve the Corners

Corners can be defined using short, straight track segments, or they can be created using one or more arcs. The images below show the two most popular corner styles; Track 45 and Any Angle.

Examples of two of the corner styles, Track 45 and Any Angle, click to enlarge an image.

Note how in the first image the interactive router is maintaining an overall orthogonal/diagonal pattern for the flow of the routing. In the Any Angle style the interactive router is finding the shortest path between the start location and the cursor location - this style of routing is called Snake Routing.

Mitered Corners

The most common routing corner shape is 45 degree mitered (diagonal) corners. Switch to the Track 45 corner mode to route diagonal corners. To ensure that it is not possible to inadvertently create acute corners during routing, both interactive routing and interactive sliding include a Miter Ratio option. The Miter Ratio multiplied by the current track width equals the separation between the walls of the tightest U-shape that can be routed for that miter ratio, as shown below. Enter a positive value equal to or greater than zero. Set the Miter Ratio to zero to create a right-angle corner.

Arcs in Corners

Many designers require curved corners. Curved corners can be routed with either the Line 45/90 With Arc corner mode or the Line 90/90 With Arc corner mode. The Line 90/90 With Arc corner mode will force a 90-degree corner though, so use the Line 45/90 With Arc corner mode if the route needs to continue at 45 degrees. The arc can be interactively resized during routing using the  and  keys (hold Shift to accelerate the resizing process).

When a curved corner style is selected during interactive routing, the glossing engine will favor a tangential path around existing curved objects. That is, the arc placed to create the corner is located and radially sized to exactly curve around the existing object. This is designed to form smooth routing through a sea of curved shapes, for example, the escape via pattern under a BGA. If the Routing Gloss Effort is set to Strong it can result in the straight track segments between the arcs being placed at an angle other than horizontal or vertical.

If you require all of the straight track segments to placed exactly horizontal or vertical, with curved corners, it can be more efficient to route with diagonal corners and then gloss the routing to curve the corners. This is achieved by setting the Hugging Style set to Rounded, and then running the Retrace Selected command. Retrace is used rather than the Gloss Selected because Retrace does not attempt to shorten the route path and reduce the number of corners, instead it focuses on glossing along the same path, in accordance with the current design rule settings. Glossing is discussed below.

Curving the corners of existing routing.

Snake Routing

As well as using the arc corner modes as just discussed, a style of smooth flowing, point-to-point routing can also be achieved by setting the corner style to Any Angle and the Routing Gloss Effort to Strong. This creates what is referred to as Snake Routing. Use this when the routing requires any angle routes to flow through multiple curved objects, as shown in the example video below.

Snake routing, with the corner style set to Any Angle.

Automatic Connection Completion

The Interactive Router is able to attempt automatic completion (Auto-Complete) of connections to the target pad, hold Ctrl and Left Click to instruct the Interactive Router to attempt to complete the current connection. This can make routing much faster than placing individual track segments, however, there are some limitations to the Auto-Complete feature, as follows:

• The start point and target pad must reside on the same layer.
• The route can be completed in accordance with design rules (provided that routing conflicts are not being ignored).

Auto-Complete is available at any time, and you can even Ctrl+click directly on a pad or connection line to route it, there is no need to select it first. You can use Auto-Complete on connections that are partially routed as well. To do this, Ctrl+click on the end of the last track segment, or the remaining connection line, to complete it to the target.

Quick Routing and Quick Differential Pair Routing Tools

The Quick Routing and Quick Differential Pair Routing commands (accessed from the main menu and the Active Bar) offer lighter routing with less settings and capabilities, suitable for simpler designs. Their general behavior and shortcuts is the same as the standard Interactive Routing and Interactive Differential Pair Routing commands.

Capabilities include:

• A number of routing modes, such as: stop at first obstacle, walkaround, and push and shove.
• Powerful dragging capabilities that maintains track angles and orthogonality.
• A loop removal feature that makes re-routing a quick and easy process.

The Quick Routing tools help maximize routing efficiency and flexibility in an intuitive way, including following cursor path for laying route sections, single-click routing completion, pushing or walking around obstacles, and automatically following existing connections, all in accordance with applicable design rules.

This router is referred to as Quick because it offers a reduced feature-set. Features that are not included in the Quick Router/Quick Differential Pair Router include:

• No turn smoothing
• Little support for Any Angle routing
• No pushing of T-junctions
• Simple Push&Shove support
• No Miter Ratio, Min Arc, or Pad Entry Stability
• Simple Gloss Effort, with no support for Gloss Neighbor
• No differential pair convergence when exiting the start pins laterally (Quick Differential Pair Router command)
• No hugging by routed differential pairs (Quick Differential Pair Router command)
• No differential pair maintenance when a neighbor differential pair is pushed (Quick Differential Pair Router command)

If you need any of these features, use the Interactive Routing and Interactive Differential Pair Routing tools.

The following collapsible sections contain information about the Quick Interactive Routing options and controls available:

Net Information

• Net Name – displays the name of the net to which the interactive routing is connected.
• Net Class – displays the net class that the interactive routing belongs to (if it is a member of a net class).
• Length – the total Signal Length. The Signal Length is the accurate calculation of the total node-to-node distance. Placed objects are analyzed to resolve stacked or overlapping objects and wandering paths within pads, and via lengths are included.
• Delay – the total delay of the selected segments, including those unrouted.

Select the clickable links of the Net Name, Net Class, Length, and Delay from the Interactive Routing mode of the Properties panel to be redirected to the PCB – Nets panel, where you may view and change details of the nets associated.

Properties

• Layer – use the drop-down to specify on which layer the routing is located.
• Via – if the via is associated with a template, the template name is displayed here.
• Via Diameter – specify the via diameter.
• Via Hole Size – specify the via hole size.
• Width – use the drop-down to specify the width.
  • Min – signifies that the design rule minimum width defined for the current net will be used
  • Preferred – signifies that the design rule preferred width defined for the current net will be used.
  • Max – signifies that the design rule maximum width defined for the current net will be used.

Interactive Routing Options

• Routing Mode – use the drop-down or use the Shift+R shortcut to cycle through the desired routing modes. The following choices are available:
  • Ignore Obstacles – select to ignore existing objects (routing can be freely placed). Violations are highlighted.
  • Walkaround Obstacles – select to have the Interactive Router route around existing tracks, pads, and vias. If this mode cannot walk around an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • Push Obstacles – select to have the Interactive Router move existing tracks out of the way. This mode can also push vias to make way for the new routing. If this mode cannot push an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • HugNPush Obstacles – select to have the Interactive Router hug existing tracks, pads, and vias as closely as possible and where necessary, push obstacles to continue the route. If this mode cannot hug or push an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • Stop At First Obstacle – in this mode, the routing engine will stop at the first obstacle that gets in the way.
  • AutoRoute Current Layer – select to enable auto-routing only on the current layer.
  • AutoRoute MultiLayer – select to enable auto-routing on multiple layers.
• Corner Style – select the desired routing corner style or use the Shift+Spacebar shortcut to cycle through the corner styles.
• Gloss Effort (Routed) – select the desired gloss level directly from the panel or use the Shift+Ctrl+G shortcut to cycle through the following choices:
  • Off – in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after routing/dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required (for example, when manually dragging tracks, cleaning pad entries, etc.).
  • Weak – in this mode, a low level of glossing is applied with the Interactive Router considering only those tracks directly connected to or in the area of the tracks that you are currently routing (or tracks/vias being dragged). This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical traces.
  • Strong – in this mode, a high level of glossing is applied with the Interactive Router looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly.
• Gloss Effort (Neighbor) – select the desired gloss level to apply to traces being pushed by the net currently being routed directly from the panel through the following choices:
  • Off – in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after routing/dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required (for example, when manually dragging tracks, cleaning pad entries, etc.).
  • Weak – in this mode, a low level of glossing is applied with the Interactive Router considering only those tracks directly connected to or in the area of the tracks that you are currently routing (or tracks/vias being dragged). This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical traces.
  • Strong – in this mode, a high level of glossing is applied with the Interactive Router looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly.
• Automatically Remove Loops – enable to automatically remove any redundant loops that are created during manual routing. This allows you to re-route a connection without having to manually remove redundant tracks. However, there are times when you need to route nets such as power nets and you need loops. You can toggle this option for a selected net by using the Shift+D shortcut to override this global setting for the same net.
• Remove Loops With Vias – enable to automatically remove loops with vias. Disable this option for vias to remain during loop removal.
• Remove Net Antennas – enable this option to remove any track or arc end that is not connected to any other primitive and forms an antenna.
• Display Clearance Boundaries – enable to have the no-go clearance area defined by the existing objects and the applicable clearance rule displayed as shaded polygons within a local viewing circle or use the Ctrl+W shortcut to toggle on or off during routing. This option is not available in the Ignore Obstacles routing mode.
  • Reduce Clearance Display Area – enable to use a smaller clearance boundary. This option is available only when the Display Clearance Boundaries option is enabled.
• Show Length Gauge – enable to display the length gauge, which shows the current routed length. The gauge settings are calculated from the set of constraints defined by the applicable design rules. Use the Shift+G shortcut to toggle the display on or off during routing.

Rules

Constraints defined by the applicable design rules will be listed under the Rules section of the Properties panel.

• Via Constraint – click to open the Edit PCB Rule dialog in which you can define PCB rules for a via.
• Width Constraint- click to open the Edit PCB Rule dialog in which you can define PCB rules for routing width.

The following collapsible sections contain information about the Quick Differential Pair Routing options and controls available:

Net Information

• DP Name – displays the differential pair name.
• DP Class – displays the differential pair class that the routing belongs to (if it is a member of a differential pair class).
• Selected
  • Length – the total length sum of the selected segments.
  • Delay – the total delay of the selected segments, including those unrouted.
• Total
  • Length – the total Signal Length. The Signal Length is the accurate calculation of the total node-to-node distance. Placed objects are analyzed to resolve stacked or overlapping objects and wandering paths within pads, and via lengths are included. If the net is not completely routed, the Manhattan (X + Y) length of the connection line is also included.
  • Delay – the delay of the routed segments of the Total Length.

Select the clickable links of the DP Name, DP Class, Length, and Delay from the Differential Pair Routing mode of the Properties panel to be redirected to the PCB – Nets panel, where you may view and change details of the nets associated.

Properties

• Layer – use the drop-down to specify on which layer the routing is located.
• Gap – use the drop-down or the Shift+6 shortcut to cycle through the permissible clearances.
  • Min – select to specify the minimum permissible clearance between primitives on different nets within the same differential pair.
  • Preferred – select to specify the preferred clearance between primitives on different nets within the same differential pair.
  • Max – select to specify the maximum permissible clearance between primitives on different nets within the same differential pair.
• Via – if the via is associated with a template, the template name is displayed here.
• Via Diameter – specify the via diameter.
• Via Hole Size – specify the via hole size.
• Width – use the drop-down to specify the width.
  • Min – signifies that the design rule minimum width defined for the current net will be used
  • Preferred – signifies that the design rule preferred width defined for the current net will be used.
  • Max – signifies that the design rule maximum width defined for the current net will be used.

Interactive Routing Options

• Routing Mode – use the drop-down or use the Shift+R shortcut to cycle through the desired routing modes. The following choices are available:
  • Ignore Obstacles – select to ignore existing objects (routing can be freely placed). Violations are highlighted.
  • Walkaround Obstacles – select to have the Interactive Router route around existing tracks, pads and vias. If this mode cannot walk around an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • Push Obstacles – select to have the Interactive Router move existing tracks out of the way. This mode can also push vias to make way for the new routing. If this mode cannot push an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • HugNPush Obstacles – select to have the Interactive Router hug existing tracks, pads, and vias as closely as possible and where necessary, push obstacles to continue the route. If this mode cannot hug or push an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • Stop At First Obstacle – in this mode, the routing engine will stop at the first obstacle that gets in the way.
  • AutoRoute Current Layer – select to enable auto-routing only on the current layer.
  • AutoRoute MultiLayer – select to enable auto-routing on multiple layers.
• Corner Style – select the desired routing corner style or use the Shift+Spacebar shortcut to cycle through the corner styles.
  • Restrict to 90/45 – enable to restrict the routing to 90 degrees and 45 degrees only.
• Automatically Remove Loops – enable to automatically remove any redundant loops that are created during manual routing. This allows you to re-route a connection without having to manually remove redundant tracks. However, there are times when you need to route nets, such as power nets and when you need loops; you can toggle this option for a selected net by using the Shift+D shortcut to override this global setting for the same net.
• Remove Loops With Vias – enable to automatically remove loops with vias. Disable this option for vias to remain during loop removal.
• Remove Net Antennas – enable this option to remove any track or arc end that is not connected to any other primitive and forms an antenna.
• Display Clearance Boundaries – enable this option to have the no-go clearance area defined by the existing objects and the applicable clearance rule displayed as shaded polygons within a local viewing circle. This option is not available in the Ignore Obstacles routing mode.
  • Reduce Clearance Display Area – enable this option to use a smaller clearance boundary. This option is available only when the Display Clearance Boundaries option is enabled.

Rules

Constraints defined by the applicable design rules will be listed under the Rules section of the Properties panel.

• Via Constraint – click to open the Edit PCB Rule dialog in which you can define PCB rules for a via.
• Differential Pair Constraint – click to open the Edit PCB Rule dialog in which you can define PCB rules for the differential pair.

Interactive Multi-Routing

When routing a PCB it is fairly common for groups of signals to all need to be routed along the same path, such as for Address and Data busses. One option would be to route each of these signals individually but a much faster option is to route them collectively. The Interactive Multi-Routing command accessed from the main Route menu or the Active Bar allows you to do just that - route multiple nets simultaneously.

Before choosing the command, select the source pad of each net to be included in the route. Shift+click to select individual pads, Ctrl+click and drag to draw a selection rectangle and sub-select multiple child pads in a component.

After launching the command, you will be prompted to click to begin multi-routing. Simply click within the design space at the point where you require to lay down the first set of track segments, then continue routing as required toward your target destination. Use the B (Shift+B) shortcut to decrease (increase) bus spacing in increments of the current grid. Press C to converge bus spacing to the minimum allowed by the applicable routing rules. Use the same shortcuts as for the Interactive Routing to perform other action: cycle through conflict resolution modes, switch routing layers, etc.

During interactive multi-routing, press Tab to open the Properties panel in its Multi-Routing mode. The following collapsible sections contain information about the options and controls available:

Properties

• Layer – use the drop-down to specify on which layer the routing is located.
• Via Template – if the via is associated with a template, the template name is displayed here.
• Via Hole Size – specify the via hole size or use the 4 shortcut key during routing.
• Via Diameter – specify the via hole diameter.
• Width – use the slider bar to specify the width. Farther to the left (Min) signifies that the design rule minimum width defined for the current net will be used. Preferred signifies that the design rule preferred width defined for the current net will be used. Farther to the right (Max) signifies that the design rule maximum width defined for the current net will be used.
  • Pickup From Existing Routes – enable to use the existing track width when routing from a placed track. That is, even if the current routing width is different to the existing track, the existing track width will be adopted when you continue the route from it.
• Bus Spacing – enter the desired bus routing or use the Shift+B shortcut.
  • From Rule – click to assign bus spacing based on the existing design rule.

Interactive Routing Options

• Routing Mode – use the drop-down or use the Shift+R shortcut to cycle through the desired routing modes. The following choices are available:
  • Ignore Obstacles – select to ignore existing objects (routing can be freely placed). Violations are highlighted.
  • Walkaround Obstacles – select to have the Interactive Router route around existing tracks, pads and vias. If this mode cannot walk around an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • Push Obstacles – select to have the Interactive Router move existing tracks out of the way. This mode can also push vias to make way for the new routing. If this mode cannot push an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • HugNPush Obstacles – select to have the Interactive Router hug existing tracks, pads, and vias as closely as possible and, where necessary, push obstacles to continue the route. If this mode cannot hug or push an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • Stop At First Obstacle – in this mode, the routing engine will stop at the first obstacle that gets in the way.
  • AutoRoute Current Layer – select to enable auto-routing only on the current layer.
  • AutoRoute MultiLayer – select to enable auto-routing on multiple layers.
• Corner Style – select the desired routing corner style or use the Shift+Spacebar shortcut to cycle through the corner styles.
  • Restrict to 90/45 – enable to restrict the routing to 90 degrees and 45 degrees only.
• Gloss Effort (Routed) – select the desired gloss level directly from the panel or use the Shift+Ctrl+G shortcut to cycle through the following choices:
  • Off – in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after routing/dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required (for example, when manually dragging tracks, cleaning pad entries, etc.).
  • Weak – in this mode, a low level of glossing is applied with the Interactive Router considering only those tracks directly connected to or in the area of the tracks that you are currently routing (or tracks/vias being dragged). This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical traces.
  • Strong – in this mode, a high level of glossing is applied with the Interactive Router looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly.
• Gloss Effort (Neighbor) – select the desired gloss level to apply to traces being pushed by the net currently being routed directly from the panel through the following choices:
  • Off – in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after routing/dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required (for example, when manually dragging tracks, cleaning pad entries, etc.).
  • Weak – in this mode, a low level of glossing is applied with the Interactive Router considering only those tracks directly connected to or in the area of the tracks that you are currently routing (or tracks/vias being dragged). This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical traces.
  • Strong – in this mode, a high level of glossing is applied with the Interactive Router looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly.
• Automatically Terminate Routing – when enabled, when you complete a route to the target pad, the routing tool does not continue in routing mode from the target pad but rather resets and is ready for you to click on the next source pad from which to route. If this option is disabled, after you route to the target pad, the tool will remain in routing mode and use the previous target pad as the source for the next route.
• Automatically Remove Loops – enable to automatically remove any redundant loops that are created during manual routing. This allows you to re-route a connection without having to manually remove redundant tracks. However, there are times when you need to route nets such as power nets and you need loops – you can toggle this option for a selected net by using the Shift+D shortcut to override this global setting for the same net.
• Remove Net Antennas – enable this option to remove any track or arc end that is not connected to any other primitive and forms an antenna.
• Allow Via Pushing – check this option to allow pushing a Via when in Push Obstacles or HugNPush Obstacles mode.

Rules

Constraints defined by the applicable design rules will be listed under the Rules section of the Properties panel.

• Via Constaint – click to open the Edit PCB Rule dialog to view/edit the rule.
• Width Constraint – click to open the Edit PCB Rule dialog to view/edit the rule.

Glossing - Smoothing the Routes

Whenever you move the cursor to define a new route path, all of the proposed routing is automatically glossed. Glossing will attempt to reduce the path length, and also improve the shape of corners and reduce their number, generally resulting in neater routing created from fewer segments.

Glossing has three settings; Off, Weak and Strong. Use the Ctrl+Shift+G shortcut to cycle through the settings during interactive routing or interactive sliding, or press Tab to open the Properties panel and select the setting:

• Off - in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after routing/dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required (for example, when manually dragging tracks, cleaning pad entries, etc.).
• Weak - in this mode, a low level of glossing is applied, with the Interactive Router considering only those tracks directly connected to or in the area of the tracks that you are currently routing (or tracks/vias being dragged). This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical routes.
• Strong - in this mode, a high level of glossing is applied with the Interactive Router looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly. Note that when Strong glossing is combined with one of the arc in corner modes, it also allows any-angle traces. The assumption here is that since the designer is curving the corners they will be comfortable with non-orthogonal routing between corners.

Along with the current Gloss Effort setting, Glossing also obeys these settings:

• Corner Style
• Hugging Style (during Interactive Sliding and also when the Gloss Selected or Retrace Selected commands are run)
• Miter Ratio
• Min Arc Ratio

Using these options, Glossing controls how tightly a corner is created and how the curved shape is formed in the route around a curved obstacle.

Existing routing can be glossed by running the Route » Gloss Selected command. Use this to your advantage to perform design changes, such as converting mitered corners to arcs, by configuring the Corner Style before running the command.

► Learn more about Post Route Glossing and Retracing

Modifying Existing Routes

One of the most common tasks in routing is to modify the existing routing. This can be done by clicking and holding on an existing segment, and sliding it to a new location. This feature, known as Interactive Sliding (because it maintains the orthogonal/diagonal patterns defined in the original routing), can call on the same set of routing technologies that are available during interactive routing.

Interactive Sliding Panel

To provide better visibility and control of the sliding process, the Properties panel includes an Interactive Sliding mode - press Tab during sliding to access the options in the panel. The default settings are configured in the PCB Editor - Interactive Routing page of the Preferences dialog.

The following collapsible sections contain information about the Interactive Sliding options and controls available:

Net Information

• Net Name – displays the name of the net to which the interactive sliding is connected.
• Net Class – displays the net class that the interactive sliding belongs to (if it is a member of a net class).
• Length – the total Signal Length. The Signal Length is the accurate calculation of the total node-to-node distance. Placed objects are analyzed to resolve stacked or overlapping objects and wandering paths within pads; and via lengths are included.
• Delay – the total delay of the selected segments, including those unrouted.

Select the clickable links of the Net Name, Net Class, Length, and Delay from the Interactive Routing mode of the Properties panel to be redirected to the PCB – Nets panel, where you may view and change details of the nets associated

Properties

• Gloss Effort (Routed) – select the desired gloss level from the panel or use the Shift+Ctrl+G shortcut to cycle through the following choices:
  • Off – in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after routing/dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required (for example, when manually dragging tracks, cleaning pad entries, etc.).
  • Weak – in this mode, a low level of glossing is applied with the Interactive Router considering only those tracks directly connected to or in the area of the tracks that you are currently routing (or tracks/vias being dragged). This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical traces.
  • Strong – in this mode, a high level of glossing is applied with the Interactive Router looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly.
• Gloss Effort (Neighbor) – select the desired gloss level to apply to traces being pushed by the net currently being routed directly from the panel through the following choices:
  • Off – in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after routing/dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required (for example, when manually dragging tracks, cleaning pad entries, etc.).
  • Weak – in this mode, a low level of glossing is applied with the Interactive Router considering only those tracks directly connected to or in the area of the tracks that you are currently routing (or tracks/vias being dragged). This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical traces.
  • Strong – in this mode, a high level of glossing is applied with the Interactive Router looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly.
• Hugging Style – controls how corner shapes are to be managed during interactive sliding and will affect both the tracks being slid and the tracks being pushed. During sliding use the Shift+Spacebar shortcut to cycle through the three modes.
  • 45 Degree – always use straight orthogonal/diagonal segments to create corners during sliding (use this mode for traditional orthogonal/diagonal routing behavior).
  • Mixed – use straight track segments when the objects being moved/pushed against are straight, use arcs when they are curved.
  • Rounded – use arcs at each vertex involved in the move/push. Use this mode for snake routing, and to use arcs + any angle routes when glossing (during interactive routing and manual glossing).
• Conflict Resolution – determines how you want the sliding objects to react when they encounter an existing object. Use the drop-down or use the Shift+R shortcut to cycle through the desired routing modes. The following choices are available:
  • Ignore Obstacles – select to ignore existing objects (routing can be freely placed). Violations are highlighted.
  • Walkaround Obstacles – select to have the Interactive Router route around existing tracks, pads and vias. If this mode cannot walk around an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • Push Obstacles – select to have the Interactive Router move existing tracks out of the way. This mode can also push vias to make way for the new routing. If this mode cannot push an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • HugNPush Obstacles – select to have the Interactive Router hug existing tracks, pads, and vias as closely as possible and where necessary, push obstacles to continue the route. If this mode cannot hug or push an obstacle without causing a violation, an indicator appears to show that the route is blocked.
  • Stop At First Obstacle – in this mode, the routing engine will stop at the first obstacle that gets in the way.
  • AutoRoute Current Layer – select to enable auto-routing only on the current layer.
  • AutoRoute MultiLayer – select to enable auto-routing on multiple layers.
• Vertex Action – options that are applied when you click and drag on a vertex rather than a track or arc (the vertex is the corner location where two segments meet). Use the Spacebar shortcut to cycle through the available modes during sliding.
  • Deform – break or lengthen the track segments attached to the moving vertex so that the vertex follows the cursor movement. (show animation)
  • Scale – hold the corner shape and resize and move the incoming track segments, keeping the vertex attached to the cursor. (show animation)
  • Smooth – reshape the corner smoothly, inserting arcs to create a curved corner when dragging inward (in Mixed or Rounded Hugging Style), at every vertex impacted by the sliding process. Also, add arcs when dragging outward in Rounded Hugging Style.
• Keep Coupled – check this option to ensure objects that belong to a differential pair will be dragged to the pair's partner track or via.
• Include Miters – check this option to include miters while dragging track segments.
• Merge Parallel – check this option to allow a track segment being dragged to be merged with an existing stationary segment once the dragged segment became aligned to the stationary segment.
• Allow Via Pushing – check this option to allow pushing a Via when in Push Obstacles or HugNPush Obstacles mode.
• Display Clearance Boundaries – enable to have the no-go clearance area defined by the existing objects and the applicable clearance rule displayed as shaded polygons within a local viewing circle. This option is not available in the Ignore Obstacles routing mode.
  • Reduce Clearance Display Area – enable to use a smaller clearance boundary. This option is available only when the Display Clearance Boundaries option is enabled.
• Show Length Gauge – enable to display the length gauge, which shows the current routed length. The gauge settings are calculated from the set of constraints defined by the applicable design rules. Use the Shift+G shortcut to toggle the display on or off during routing.
• Pad Entry Stability – protects centered pad entries. Use the slider bar to configure the level of protection:
  • Off = no protection
  • Max = maximum protection
• Miter Ratio – controls the minimum corner tightness. The Miter Ratio multiplied by the current track width equals the separation between walls of the tightest U-shape that can be routed for that ratio. Enter a positive value equal to or greater than zero (the x multiplier is added automatically).
• Min Arc Ratio – applied during any angle interactive routing and during interactive sliding with Mixed Hugging Style. The ratio is used to determine the minimum radius arc allowed, when the arc radius falls below this minimum the arc is replaced by track segments, where: Min Arc Radius = Min Arc Ratio x Arc Width.

Set the Minimum Arc Ratio to 0 (zero) to always use arcs.

Modifying the Routes

Examples of modifying the routing.

Tips for interactive sliding:

• Configure the Interactive Sliding options to suit the routing style used on the board - for example, the Hugging Style should be 45 Degree if your routing has diagonal corners. Press the Shift+Spacebar shortcut keys to cycle through the Hugging Style modes during sliding.
• To more easily see the objects that make up the current routing, adjust the Transparency of the routing objects in the View Configuration panel (show image).
• When you click and drag on a vertex (the point where two track ends meet) the current Vertex Action setting is applied, use the Deform mode if you want to reshape the corner. Press the Spacebar to cycle through the modes as you drag the vertex.
• The extent that the moving tracks are reshaped as you slide them is controlled by the current Gloss Effort (Routed) setting, press the Ctrl+Shift+G shortcuts to cycle through the modes during sliding. If you find that the routing will not slide how you want, try lowering the Routing Gloss Effort setting.
• The impact that the moving tracks have on the adjacent routing is controlled by the current Gloss Effort (Neighbor) setting, press Tab during sliding to change the setting.
• The routing that you are sliding will not only snap to the current snap grid, the cursor snap behavior to is also dependent on: the object snapping settings in combination with the layer snapping setting, and if the snap guides and axes snapping settings are enabled (press Ctrl+E to toggle these on/off). To temporarily inhibit snapping during interactive sliding, hold down the Ctrl key. Learn more about the PCB Grids System

► The Interactive Sliding options available in the panel are described with the Interactive Routing options, in the Interactive Routing and Interactive Sliding Options section.

Modifying T-Junctions

There are specific algorithms included to support interactively modifying a T-junction - click and drag on the junction point to modify a T-junction.

Examples of the T-Junction dragging capabilities.

Interactive Via Dragging

PCB designers can spend a lot of time adjusting the routing, perhaps due to a late design change, or to achieve completion of their design. This can mean pushing and shoving of existing routing, dragging vias, and nudging components.

Adjust the via dragging behavior in the Properties panel.

Complementing the support for glossing of neighbor routes, via dragging is also supported. Via dragging supports Neighbor Glossing, configured through the Interactive Via Dragging mode of the PCB editor's Properties panel. Press Tab during via dragging to access the panel and adjust the settings.

Press Tab as you drag to configure the Via Dragging options.

The following collapsible sections contain information about the Interactive Via Dragging options and controls available:

Properties

• Gloss Effort (Routed) – select the desired gloss level of the traces connected to vias being dragged from the panel or use the Shift+Ctrl+G shortcut to cycle through the following choices:
  • Off – in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required.
  • Weak – in this mode, a low level of glossing is applied with the routing engine considering only those tracks directly connected to vias being dragged. This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical traces.
  • Strong – in this mode, a high level of glossing is applied with the routing engine looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly.
• Gloss Effort (Neighbor) – select the desired gloss level to apply to traces being pushed by the via currently being dragged directly from the panel through the following choices:
  • Off – in this mode, glossing is essentially disabled. Note, however, that cleanup is still run after dragging occurs to eliminate, for example, overlapping track segments. This mode is typically useful at the end stage of board layout when the ultimate level of fine-tuning is required.
  • Weak – in this mode, a low level of glossing is applied with the routing engine considering only those tracks directly connected to vias being dragged. This mode of glossing is typically useful for fine-tuning track layout or when dealing with critical traces.
  • Strong – in this mode, a high level of glossing is applied with the routing engine looking for shortest paths, smoothing out tracks, etc. This mode of glossing is typically useful in the early stages of the layout process when the aim is to get a good amount of the board routed quickly.
• Hugging Style – controls how corner shapes are to be managed during interactive via dragging and will affect both the tracks connected to vias being dragged and the tracks being pushed. During via dragging, use the Shift+Spacebar shortcut to cycle through the three modes.
  • 45 Degree – always use straight orthogonal/diagonal segments to create corners during dragging (use this mode for traditional orthogonal/diagonal routing behavior).
  • Mixed – use straight track segments when the objects being moved/pushed against are straight, use arcs when they are curved.
  • Rounded – use arcs at each vertex involved in the move/push.
• Conflict Resolution – determines how you want the dragged objects to react when they encounter an existing object. Use the drop-down or use the Shift+R shortcut to cycle through the desired modes. The following choices are available:
  • Ignore Obstacles – select to ignore existing objects (routing can be freely moved). Violations are highlighted after dragging.
  • Walkaround Obstacles – select to have the routing engine place tracks around existing tracks, pads and vias where possible.
  • Push Obstacles – select to have the routing engine move existing routing out of the way where possible. This mode can also push vias.
  • HugNPush Obstacles – select to have the routing engine hug existing tracks, pads, and vias as closely as possible and where necessary, push obstacles to continue the route.
  • Stop At First Obstacle – in this mode, the routing engine will stop at the first obstacle that gets in the way.
• Keep Coupled – enable this option to attempt to drag the partner via when dragging a via that belong to a differential pair. 
• Allow Via Pushing – enable this option to allow pushing vias when in Push Obstacles or HugNPush Obstacles Conflict Resolution mode.
• Pad Entry Stability – protects centered pad entries. Use the slider bar to configure the level of protection:
  • Off = no protection
  • Max = maximum protection
• Miter Ratio – controls the minimum corner tightness. The Miter Ratio multiplied by the current track width equals the separation between walls of the tightest U-shape that can be routed for that ratio. Enter a positive value equal to or greater than zero (the x multiplier is added automatically).
• Min Arc Ratio – applied interactive via dragging with Mixed Hugging Style. The ratio is used to determine the minimum radius arc allowed, when the arc radius falls below this minimum the arc is replaced by track segments, where: Min Arc Radius = Min Arc Ratio x Arc Width.

Differential Pair Dragging

To recognize the members in a differential pair, the concept of Coupling is used. When software recognizes objects that belong to a differential pair it will attempt to drag the pair's partner track or via if the Keep Coupled option is enabled in the Interactive Sliding or the Interactive Via Dragging modes of the Properties panel.

Press X as you drag a via-pair to rotate the pair by 90 degrees.

To confirm that the partner objects are coupled, the software checks that the objects:

• For via pairs - belong to the pair, and are closer than 2 * Preferred Gap
• For track pairs - belong to the pair, are on the same layer, are separated by no more than the Preferred Gap

Interactive Routing and Interactive Sliding Options

Whether you're interactively routing a connection or dragging an existing route to make way for more routing, the same set of routing technologies are applied. This section summarizes the options available in the Interactive Routing and the Interactive Sliding modes of the Properties panel. The default settings for many of these options are configured in the PCB Editor - Interactive Routing page of the Preferences dialog.

Interactive Routing and Interactive Sliding Options

Gloss Effort (Routed)

During a route event, such as interactive routing, interactive sliding, or ActiveRouting, the software runs the glossing engine. The glossing engine constantly reviews all of the segments placed or impacted by the current route event, attempting to improve the quality of the results. Measures of quality include: reducing the number of corners, reducing the number of segments, removing acute angles and reducing the overall route length.

Glossing has three settings; Off, Weak and Strong. These settings are discussed in the Glossing - Smoothing the Routes section.

Gloss Effort (Neighbor)

Gloss Effort (Neighbor) configures the amount of glossing applied to adjacent routes that are impacted by the current interactive routing or sliding. It also has three settings; Off, Weak and Strong.

Hugging Style

This option controls how corner shapes are to be managed during interactive sliding and will affect both the tracks being slid and the tracks being pushed. During sliding use the Shift+Spacebar shortcut to cycle through the three modes.

• 45 Degree - always use straight orthogonal/diagonal segments to create corners during sliding (use this mode for traditional orthogonal/diagonal routing behavior).
• Mixed - use straight track segments when the objects being moved/pushed against are straight, use arcs when they are curved.
• Rounded - use arcs at each vertex involved in the move/push. Use this mode for snake routing, and to use arcs + any angle routes when glossing (during interactive routing and manual glossing).

Routing Mode / Sliding Mode

This option determines how you want the routing/sliding objects to react when they encounter an existing object. Use the Shift+R shortcut to cycle through the available modes during routing or sliding.

These are the modes that are referred to as the Routing Conflict Resolution modes in the PCB Editor - Interactive Routing page of the Preferences dialog.

Vertex Action

To better support the designer's need to easily manipulate and re-shape the existing routing, there are specific options that are applied when you click and drag on a vertex rather than a track or arc (the vertex is the corner location where two segments meet). Use the Spacebar shortcut to cycle through the available modes during sliding.

• Deform - break or lengthen the track segments attached to the moving vertex so that the vertex follows the cursor movement.
• Scale - hold the corner shape and resize and move the incoming track segments, keeping the vertex attached to the cursor.
• Smooth - reshape the corner smoothly, inserting arcs to create a curved corner when dragging inward (in Mixed or Rounded Hugging Style), at every vertex impacted by the sliding process. Also add arcs when dragging outward in Rounded Hugging Style.

Checkbox Options

• Automatically Terminate Routing - when the current connection being routed reaches the target pad, automatically stop routing that net but remain in the Interactive Routing command, ready to start routing another net.  
• Automatically Remove Loops - when this option is enabled you can route a new path for an existing route - when the new route path comes back to meet the existing path the redundant loop is automatically removed. Learn more about Modifying the Routing.
• Remove Net Antennas - a net antenna is a short, unterminated track (arc) segment. These are automatically removed if the current routing impacts on an object that the antenna is touching.
• Allow Via Pushing - during routing/sliding in Push or Hug & Push modes, allow existing vias to also be pushed.
• Display Clearance Boundaries - display the no-go area around existing objects, defined by the applicable Clearance design rule(s).
  • Reduce Clearance Display Area - reduce this display to a circular zone around the current cursor location.
• Show Length Gauge - the length gauge indicates how well the current route is meeting applicable Length and Matched Length design rules. Learn more about Length Tuning.

Pad Entry Stability

The Pad Entry Stability slider protects centered pad entries, preventing Glossing from un-centering a centered track (it holds a centered track on-center, it does not center an un-centered track). Use the slider bar to configure the level of protection:

• Off = no protection
• Max = maximum protection

Miter Ratio

The Miter Ratio controls the minimum corner tightness. The Miter Ratio multiplied by the current track width equals the separation between walls of the tightest U-shape that can be routed for that ratio, as shown in the Mitered Corners description, earlier on this page. Enter a positive value equal to or greater than zero (the x multiplier is added automatically).

Min Arc Ratio

The Min Arc Ratio is applied during any angle interactive routing and also during interactive sliding with Mixed Hugging Style. The ratio is used to determine the minimum radius arc allowed, when the arc radius falls below this minimum the arc is replaced by track segments, where:

Min Arc Radius = Min Arc Ratio x Arc Width

• This setting is not applied during any arc in corner routing or interactive sliding with Rounded Hugging Style, as these modes do not use segmented arcs.
• Set the Minimum Arc Ratio to 0 (zero) to always use arcs.

Controlling the Routing Width and Via Size as You Route

When you run the Interactive Routing command and click to start routing, a series of track objects are created from the nearest pad up to the current cursor location. The width of these tracks is determined by the current Track Width Mode setting, which is displayed on the status bar during routing (shown in the video below).

There are four possible Routing Width Source settings:

• the designer's preferred width, referred to as User Choice (which must be within the range allowed by the applicable Routing Width design rule); or
• the Minimum, Preferred, or Maximum value of the applicable Routing Width design rule.

The selection of User Choice / Min rule / Preferred rule / Max rule is stored in and can be selected using the Track Width Mode drop-down on the PCB Editor - Interactive Routing page of the Preferences dialog.

Changing the Track Width Mode While Routing

You can cycle through the four routing width options by pressing the 3 shortcut key during interactive routing, as shown in the video below. The current mode is displayed on the Status bar. If you forget any of the in-command shortcuts, press Shift+F1 to display a list while running the command.

To change the track width source while routing, press the 3 key on the keyboard. Press Shift+W to select a different value for the User Width.

When you change the track width mode, you move between the values defined in the applicable design rule (Min/Preferred/Max), and User Choice.

If you select User Choice, the track width will be:

• the width of existing routing if the Pickup Track Width from Existing Routing option is enabled and the click location is on an existing route, or
• the last-used User-Choice width if it falls within the range defined by the applicable rule for the net you are routing. If it does not, the width will be clipped to the nearest value that is within the range allowed by the rule.

Changing the User Choice Routing Width While Routing

To change the width while routing, the following shortcuts are used. Note that if the Interactive Routing Width Sources options were set to one of the Rule-based width options, that option is changed to User Choice whenever one of these shortcuts is used.

• Shift+W - use this shortcut during routing to open the Choose Width dialog. Click on a new width to close the dialog and continue routing at the chosen width. Available widths can be edited by clicking the Favorite Interactive Routing Widths button on the PCB Editor - Interactive Routing page of the Preferences dialog.
• Tab - use this shortcut if the required width is not defined as a favorite. Pressing Tab will open the Properties panel in Interactive Routing mode. The current editing session will pause and the panel will open with the current Width selected. Type in a new width value then press Enter to continue routing at the new width. Alternatively, after typing in a new width value, click the pause button overlay to resume routing. To resume routing without editing the value, press Esc.

Remember, if you use one of these techniques to change the width during routing, the Track Width Mode is automatically changed to User Choice.

Changing Layers and adding a Via While Routing

There are two approaches to interactively change layers during routing:

• Press the * key on the numeric keypad. Each press of that key will move you down to the next available signal layer.
• Use the Ctrl+Shift+Wheel Scroll shortcut combination. Hold the Ctrl+Shift keys then scroll the mouse wheel forwards to move down through the available signal layers; scroll the mouse wheel backwards to move up through the available signal layers. Note that this shortcut can be used at any time to change layers. If you are not currently routing, this shortcut combination will step through all enabled layers.

A via is automatically added at the last corner where the last two segments meet. As with the routing width, the size of the via is determined by the current Via Size Mode as shown in the video below. The mode can be pre-configured in the Interactive Routing Width Sources option.

Use the Ctrl+Shift+Scroll shortcut to change layers, and the 4 shortcut key to cycle through the via size choices.

Changing the Via Size Mode While Routing

As with the routing width, there are four possible options for selecting the via size during interactive routing:

• the designer's preferred via size (User Choice); or
• the Minimum, Preferred or Maximum value of the applicable Routing Via Style design rule.

You can cycle through the four via size options by pressing the 4 shortcut key during interactive routing. The current mode is displayed on the Status bar as shown in the video above. 

Changing the User Choice Via Size While Routing

To change the User Choice via size while routing:

• Shift+V - press this shortcut during interactive routing to open the Choose Via Size dialog. The dialog will automatically list all via sizes currently used in the design. Select a via size then click OK to make that the User Choice via size.

• Tab - as well as changing the track width during routing, when you press Tab to open the Properties panel in Interactive Routing mode you can also change the Via Diameter. As with the track width, the size you enter must be between the minimum and maximum values defined in the applicable Routing Via Style design rule.

Changing the Via Type While Routing

If there are multiple Via Types defined, during a layer change there may be more than one Via Type available for the layers being spanned. An example would be when there is a blind via available between the top and mid1 layers and there is also a top-bottom Via Type available. If you are performing a layer change and there is more than one Via Type available, you can press the 6 shortcut to cycle through the possible Via Type options (or press the 8 shortcut to display a list). Refer to the Defining the Via Types page for more detailed information. Additionally, the last-used via stack is retained as the default for the next net you route. The default via stack is retained for the current editing session only.

Stacked µVias being placed during a layer change from L1 to L4. The Interactive Routing mode of the Properties panel displays the Via Type(s) that will be placed. Press 6 to cycle through the possible via stacks; press 8 to display a list of possible via stacks.

Via Behavior when using the Look Ahead Routing Segment

During interactive routing the track segments that are yet to be placed are shown as hatched and the committed segments are solid. There is another mode, where the last segment connected to the cursor is displayed as hollow (an outline), this segment is referred to as the Look Ahead segment. When you are routing in Look Ahead mode all hatched segments are placed when you click, but the hollow segment is not. The idea is that you can use the Look ahead segment to accurately place the previous segment(s), without committing the last segment. Press the 1 shortcut during routing to toggle the Look Ahead mode on and off.

If you toggle the Look Ahead mode on during a layer change the via will jump from the cursor back to the previous corner, because the Look Ahead segment will not be placed when you click. The video below demonstrates the behavior.

If you press 1 to toggle the Look Ahead mode on and off during a layer change, the via will jump back to the end of the last ready-to-place segment.

Controlling SMD Pad Entries

The SMD To Corner and SMD Entry design rules can impact the routing process. You will need to set up the necessary design rules before starting the routing process so that you can control how tracks enter and exit an SMD pad. Open the PCB Rules and Constraints Editor dialog (click Design » Rules from the main menus) to create and configure these design rules.

In the SMD to Corner design rule, the distance to corner value should be greater than the width of the track or the applicable clearance rule (whichever is greater). If it must be less than that, there are three ways you can approach this:

• Press the Spacebar while performing the pad entry. This can help align the last track segment along the pad center.
• Commit the routing close to the pad then perform the pad entry without glossing (glossing can be temporary disabled by holding down Ctrl+Shift).
• If performing the pad entry with more than one possible entry, move the mouse inside the pad. That allows you to choose where you want your SMD entry. 

Automatically Changing the Routing Width As You Route

A common challenge with modern component technology is needing to route a net at different widths as the routing travels across the board. For example, routing into or out of a BGA will often require narrower escape routes, switching to the preferred width at the edge of the BGA footprint. 

This can be achieved manually during interactive routing using the techniques described previously on this page. You can also automate this width-switching behavior by adding a placement room and a room-based routing width rule. Once this has been done, tracks will automatically neck and expand as the room is entered or exited.

The feature works by:

• Defining a Placement Room rule for the region of the board that requires narrower routes.
• Defining a Width Constraint rule of a higher priority that defines the width of the routes within the room. This rule will use the TouchesRoom scope as discussed below.

Once this has been done, the width will change automatically as you route into or out of the placement room as shown in the videos below.

Width rules are obeyed and track segments are intelligently sized as the room boundary is crossed.

Room-based routing requires a placement room to be defined first. A placement room is also a design rule. While you can create the rule then define the room from the design rule dialog, it can be more efficient to do it the other way around, interactively create the room; Altium Designer creates the design rule for you.

Creating the Room Rule

The Design » Rooms submenu has a number of room definition commands.

Rooms are a useful feature for controlling where components are placed and also for controlling what rules are applied within that area of the board.

A room created around selected components will result in the following:

1. A Component Class of the selected components is created. Review the class (Design » Classes) and update the Component Class Name as required.
2. A Placement Room Definition design rule is created. The rule is scoped to target the Component Class created in step 1. If you changed the Component Class name, the rule scope (Full Query) must be updated to match.
3. The Placement Room Definition design rule is also automatically named. Update the name as required and take note of the name because the room will be referenced in other design rules by its Name.
4. If required, resize the room. To do this, click once to select it then click and hold on a vertex to move a corner or an edge. After clicking on a vertex to move it, you can also press Shift to perform a symmetrical resize.

In this example, the rule has been scoped to target a specific BGA footprint ('BGA50P18X18-180') rather than a component class.

Creating the Room-based Routing Rule

Once the room that defines the area requiring a different routing width has been defined, the routing width rule can then be created. The image below shows an example of a Routing Width rule that is scoped to instruct the PCB editor to set the routing width to 0.075mm whenever the routing touches the room named Room_BGA. Altium Designer's interactive routing engine will automatically terminate the current track segment and start a new segment at the room boundary to satisfy a rule such as this.

A Routing Width design rule scoped to set the width of all nets to 0.075mm within the room Room_BGA. Note that this rule appears first in the tree indicating that it is the highest priority routing width rule.

► Learn more about the TouchesRoom and WithinRoom query keywords

Connecting Two Nets with a Net Tie Component

It is not uncommon to need to intentionally connect two different nets. An example could be when you need to connect an Analog ground and a Digital ground in a controlled way. This is achieved by connecting the two nets through a Net Tie component. A Net Tie component is nothing more than a controlled short circuit, allowing you to decide the location on the board where the nets connect.

The challenge with routing towards a Net Tie pad is the rules engine will see that a violation is about to occur, and prevent you from routing to the Net Tie pad.

• To resolve this, switch the Routing Mode to Ignore Obstacle.

To route in to a Net Tie, switch the Routing Mode to Ignore Obstacle.

► Learn more about Intentionally Connecting Two Nets

Automatic Re-Routing of a Moved Component

Component Re-route

While routing the board, it is not uncommon to need to adjust the location of a routed component to create space for new routing. This feature is accessed by enabling the Component re-route checkbox in the Dragging region on the PCB Editor - Interactive Routing page of the Preferences dialog.

During the move process, the following shortcuts can be used to invoke the specified actions:

• Component Re-route Mode (Shift+R) - toggles post-drop connectivity restoration. After the moving set has been released, the software will attempt to re-route the component(s) to reconnect any broken nets. Use the Shift+R shortcut to inhibit the re-route behavior (or disable the Component re-route option on PCB Editor - Interactive Routing page of the Preferences dialog). Current Status is displayed in the Heads Up display and on the Status bar.
• Change Component Selection (Shift+Tab) - while dragging, the set of objects being moved can still be changed. Press Shift+Tab to cycle through the following selection sets:
  • Components only, then
  • Components +Via Fanouts +Escapes +Interconnects, then
  • Initial selection set (if different from the previous two), then
  • Back to Components only.

• Display / Hide Connection Lines (N) - the N shortcut cycles through three states: no connection lines, pad-to-pad connection lines, and route-to-route connection lines. The last mode indicates where the connection lines have been severed and will possibly be restored after the selection being moved is released.
• Change Gloss Effort (Ctrl+Shift+G) - cycle through the available Routing Gloss Effort options to control the amount of gloss applied during component re-routing.

Move Component with Relevant Routing

Enable the Move component with relevant routing option in the Dragging region on the PCB Editor - Interactive Routing page of the Preferences dialog to start the move component action with the relevant routing (Components +Via Fanouts +Escapes +Interconnects). Use the Shift+Tab shortcut to cycle the selection set as described in the previous section. 

Disable the option to start the move component action with components only selected. Because the set of relevant routing objects is detected prior to the move commencing, it is not possible to use Shift+Tab to cycle through the selection set when the option is disabled.

Tracing an Existing Shape with the Interactive Router Follow Mode

A common requirement during routing is to place a route so that it follows an existing shape or contour. The contour could be an obstacle, a cutout or the board edge, or an existing route.

Rather than having to route "against" the contour using careful and accurate mouse movements and click actions to ensure the new route hugs the contour, in Follow mode, you click to nominate the contour then move the cursor along the contour to define the route direction. In Follow mode, the interactive router will add track and arc segments so that the new route follows the contour in compliance with applicable design rules. This feature is particularly useful when placing curved routes.

To use the feature:

• Launch interactive routing, click to pick a connection to route and switch to the required corner style (Shift+Spacebar).
• To follow a contour, position the cursor over the required object and press Shift+F. The Interactive Router will detect the object under the cursor and switch to Follow Mode.
• Move the cursor in the required direction; the software will automatically place track and arc segments to follow the contour in that direction.
• Left-click to place the Follow segments and drop out of Follow mode.
• Complete the route as required.

Available Routing Conflict Resolution Modes

As mentioned, how the interactive router responds to objects already in the PCB workspace, such as pads on other nets, depends on the current Routing Conflict Resolution mode. Configure which conflict resolution modes are available during routing on the PCB Editor - Interactive Routing page of the Preferences dialog.

Conflict resolution modes include:

• Ignore Obstacles – ignore existing objects (routing can be freely placed). Violations are highlighted.
• Push Obstacles – push existing tracks and vias to make room for the new route.
• Walkaround Obstacles – attempt to find a path around existing objects. The clearance to other objects is defined by the applicable Clearance design rule.
• Stop At First Obstacle – in this mode, the routing engine will stop at the first obstacle that gets in the way.
• Hug And Push Obstacles – in this mode, the routing engine will closely follow existing objects and only push them when there is insufficient room for the track being routed.
• AutoRoute on Current Layer – this mode applies auto-router intelligence to the interactive router, automatically selecting between pushing and walking around to give the shortest overall route length.
• AutoRoute on Multiple Layers – this mode applies auto-router intelligence to the interactive router, automatically selecting between pushing, walking around or switching layers to give the shortest overall route length.

Dynamic Display of Clearance Boundaries During Routing

Have you ever wondered why a route won't fit through a gap during interactive routing? Is it an incorrect rule constraint or is the net being targeted by the wrong rule? Designed to help interpret and understand the impact of design rules, the dynamic display of clearance boundaries feature shows just how much space is available during interactive routing.

The Display Clearance Boundaries feature has two modes: either display the clearance boundaries as a shaded, no-go area defined by the existing objects + the applicable clearance rule around all objects on the entire PCB; or reduce the clearance display area to a circular zone around the cursor.

The clearance around existing workspace objects can be displayed dynamically as you route. Use the Ctrl+W shortcut to enable/disable during routing.

Enabling the Dynamic Display of Clearance Boundaries

Enable the Display Clearance Boundaries option on the PCB Editor - Interactive Routing page of the Preferences dialog.

Enable the option on the PCB Editor - Interactive Routing page of the Preferences dialog.

• When the Display Clearance Boundaries option is enabled, the no-go clearance area defined by the existing objects + the applicable clearance rule is displayed as shaded polygons within a local viewing circle as as you interactively route.
• If the Reduce Clearance Display Area option is disabled, the no-go clearance area is displayed for the entire layer as shown in the video below.

The no-go area can be displayed for all copper objects on the current layer, if preferred.

Other Interactive Routing Options and Features

There are a number of other options for the interactive router that are configured on the PCB Editor - Interactive Routing page of the Preferences dialog. It is important to understand the role of these options to get the maximum benefit from the Interactive Router.

Automatically Terminate Routing

• Enable this option to automatically drop the current net when the target pad is reached. If this option is not enabled, use the Right Mouse button or Esc key to drop the current connection (typically this option is enabled).

Automatically Remove Loops

• Altium Designer provides support for Loop Removal when interactively routing your nets. As you route there will be many instances where you need to change some of the existing routing. Rather than attempting to change the existing routing using a drafting type approach of clicking and dragging track segments, an existing route path can be redefined by simply routing a new path. Start interactively routing anywhere along the existing route path, route the new path, returning to meet the old path where required. As soon as the new path meets the existing path, all segments in the redundant loop are automatically removed if the Automatically Remove Loops option is enabled (typically this option is enabled).

To re-route, simply route the new path. When the new route comes back to meet the existing route, a loop is created. Altium Designer will automatically remove this if Loop Removal is enabled.

• Note that certain nets may require loops (multiple paths to the same point), such as a power or ground net. For these nets, the Automatically Remove Loops feature can be selectively disabled by double-clicking on the net name in the PCB panel (set the panel mode to Nets) to open the Edit Net dialog in which the Remove Loops option can be turned off for only that net.  
• Loop Removal - press the Shift+D shortcut while routing to switch to allow loops mode. The interactive router will remain in this mode until toggled off (toggle feature only available during interactive routing). Existing loops will be retained if loop removal is re-enabled and a net containing loops continues to be re-routed.

Routing Gloss Effort

• As the cursor is moved during interactive routing, the routing engine continually attempts to find the shortest path from the last click location up to the current cursor location. How well it can smooth the routing and reduces the number corners is determined by the Routing Gloss Effort.
• The current Routing Gloss Effort setting is displayed on the Status bar. Use the Ctrl+Shift+G shortcut to cycle the setting. Note that the stronger the setting, the fewer corners in the final route. The current mode is shown in the Heads Up display and on the Status bar. 
• Gloss can also be temporarily inhibited during interactive routing while holding the Ctrl+Alt keys.
• Glossing is a calculation and an intensive task that runs in the background. It can affect the performance of the Interactive Router particularly when routing multiple nets simultaneously. The stronger the Gloss setting, the more time it takes to perform the calculations.

Look Ahead Behavior

• During interactive routing for the net currently being routed, the track segments are either displayed as hatched or hollow (empty). All hatched segments are placed with the next mouse click.
• The hollow segment is called the Look Ahead segment. Its purpose is to allow designers to plan ahead, i.e. to consider where the next segment might be placed without needing to commit to it. The Look Ahead mode is toggled on and off using the 1 shortcut key (while routing).

The hollow or empty segment is called the Look Ahead segment. Use it to plan where future segments will be placed.
Press the 1 shortcut during routing to toggle the Look Ahead mode on and off.

Shortcuts Available During Interactive Routing

• Use * on the numeric keypad to switch to the next available routing layer and insert a via.
• Hold Ctrl+Shift while scrolling the mouse wheel to cycle to the next available routing layer and insert a via. Each mouse wheel click moves one layer.
• Use Shift+R to cycle through the available routing conflict resolution modes.
• Use Shift+Spacebar to cycle available corner modes (learn more). For the arc in corner options, use the "," and "." keyboard buttons to decrease or increase the arc size.
• Spacebar toggles the direction of the last corner.
• Use Backspace to "rip up" the last-placed segment(s).
• Use Shift+W to open the Choose Width dialog to change the routing width.
• To switch to the next available signal layer and insert a via:
  • Press the * key on the numeric keypad, or
  • Use the Ctrl+Shift+Wheel Scroll shortcut combination.
• If you click to start routing from a thru-hole pad or a via and realize you are on the wrong layer, press the L shortcut to step through the available signal layers without adding a via.
• Use Ctrl+Click to instruct the interactive router to attempt to automatically complete the current route.
• Press Shift+F1 while routing to display the interactive routing shortcuts.
• Commands available during a layer change are: 
  • Use Ctrl+L to open a list of available layers then click to select the target layer.
  • Use the 1 to 10 number pad keys to switch immediately to that layer number.
  • Open the Properties panel to display a Z-plane view of the via that will be used for the layer change.

Where to Next?